Home » D-Link Manuals » Bridges & Routers » D-Link DWR-960 » Manual Viewer

D-Link DWR-960 Product Manual - Page 13

Configuration, Initial Connection to the Router, Connect via Ethernet Cables

Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Section 3 - Configuration Configuration This section shows you how to configure your new DWR-960 using the configuration utility that can be accessed via your web browser. Initial Connection to the Router By default, the DWR-960 comes configured to work with most 4G SIM/UICC cards. If you wish to configure the router, you will need to establish a direct connection with the router in order to access the web-based configuration utility. Refer to the following two sections for wired and wireless connection methods. Once you have configured your router, you will be able to connect to a wireless network using the Wi-Fi settings that you specified in the configuration process. Connect via Ethernet Cables If you are configuring the router from a PC with a wired Ethernet connection, plug one end of an Ethernet cable into the port labelled LAN on the back of the router, and the other end into the Ethernet port on your computer. Modem D-Link DWR-960 User Manual 9

Section	Page
Product Overview	5
Package Contents	5
System Requirements	6
Introduction	7
Hardware Overview	8
Overview	8
LED Indicators	10
Installation	11
Initial Setup	11
RESET	11
SIM	11
WPS	11
Wireless Installation Considerations	12
Configuration	13
Initial Connection to the Router	13
Connect via Ethernet Cables	13
Connect via Wi-Fi	14
Web-based Configuration	16
Configuration Utility	16
Navigation	17
Quick Access	18
Setup Wizard	19
Internet Settings	20
Network Status	20
Failover	21
Internet Settings	22
APN Settings	24
Connection Mode Settings	26
PIN Management	27
My Operator (PLMN)	28
Wi-Fi Settings	30
Wi-Fi Status	30
Basic Settings	31
Advanced Settings	33
Wi-Fi Clients	35
Settings	36
Router LAN Settings	36
DHCP Settings	37
MAC Filter	38
Firewall Settings	40
DDNS	44
System	45
Information	45
Admin Settings	46
Account	46
Language	47
Date & Time	48
Settings Profile	50
Reset / Reboot	52
Firmware Upgrade	53
System Logs	54
Parental Control	55
SMS	56
Short Messages	56
USSD	57
Connecting to a Wireless Network	58
WPS Button	58
Connecting to a Wireless Network	59
Using Windows 10	59
Using Windows 8	61
Using Windows 7	63
Using Windows® XP	66
Troubleshooting	67
Networking Basics	69
Check your IP address	69
Statically Assign an IP address	70
Technical Specifications	71

Match case Limit results 1 per page

D-Link DWR-960 User Manual

Section 3 - Conﬁguration

Conﬁguration

Initial Connection to the Router

This section shows you how to conﬁgure your new DWR-960 using the conﬁguration utility that can be accessed via your web browser.

By default, the DWR-960 comes conﬁgured to work with most 4G SIM/UICC cards. If you wish to conﬁgure the router, you will need to establish a

direct connection with the router in order to access the web-based conﬁguration utility. Refer to the following two sections for wired and wireless

connection methods. Once you have conﬁgured your router, you will be able to connect to a wireless network using the Wi-Fi settings that you

speciﬁed in the conﬁguration process.

If you are conﬁguring the router from a PC with a wired Ethernet connection, plug one end of an Ethernet cable into the port labelled LAN on the

back of the router, and the other end into the Ethernet port on your computer.

Connect via Ethernet Cables

Modem