Dell Dimension XPS P60 MT Service Manual - Page 19

Replacing the Media Card Reader

Get Dell Dimension XPS P60 MT PDF manuals and user guides View all Dell Dimension XPS P60 MT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

1 FlexBay USB cable 3 Media Card Reader 2 securing tab 7. Remove the four screws that secure the Media Card Reader to the FlexBay dock. 8. Slide the Media Card Reader out of the FlexBay dock. 1 Media Card Reader 3 FlexBay dock 2 screws (4) Replacing the Media Card Reader 1. Follow the instructions in Before You Begin. 2. Remove the new Media Card Reader from its packaging. Save the original packaging for storing or shipping the Media Card Reader. 3. Slide the Media Card Reader into the FlexBay dock. 4. Replace the four screws that secure the Media Card Reader to the FlexBay dock. 5. Lift the securing tab and slide the FlexBay dock through the front of the computer until the securing tab snaps into place. 6. Connect the FlexBay USB cable to the FLEXBAY connector on the master I/O board. For more information on the location of the connector, see Master I/O Board Components. 7. Close the PCI shroud (see Closing the PCI Shroud). 8. Replace the left side-panel (see Replacing the Left Side-Panel). 9. Lift the drive panel towards the top of your computer. 10. Connect your computer and devices to electrical outlets and then turn them on. Back to Contents Page

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
7.
Remove the four screws that secure the Media Card Reader to the FlexBay dock.
8.
Slide the Media Card Reader out of the FlexBay dock.
Replacing the Media Card Reader
1.
Follow the instructions in
Before You Begin
.
2.
Remove the new Media Card Reader from its packaging. Save the original packaging for storing or shipping the Media Card Reader.
3.
Slide the Media Card Reader into the FlexBay dock.
4.
Replace the four screws that secure the Media Card Reader to the FlexBay dock.
5.
Lift the securing tab and slide the FlexBay dock through the front of the computer until the securing tab snaps into place.
6.
Connect the FlexBay USB cable to the FLEXBAY connector on the master I/O board. For more information on the location of the connector, see
Master I/O
Board Components
.
7.
Close the PCI shroud (see
Closing the PCI Shroud
).
8.
Replace the left side-panel (see
Replacing the Left Side
-
Panel
).
9.
Lift the drive panel towards the top of your computer.
10.
Connect your computer and devices to electrical outlets and then turn them on.
Back to Contents Page
1
FlexBay USB cable
2
securing tab
3
Media Card Reader
1
Media Card Reader
2
screws (4)
3
FlexBay dock