Dell PowerEdge M640 EMC for VRTX enclosure Installation and Service Manual - Page 46

After working inside your system, Recommended tools, Removing the system from the enclosure

Get Dell PowerEdge M640 PDF manuals and user guides View all Dell PowerEdge M640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

3. Install the I/O connector cover. CAUTION: To prevent damage to the I/O connectors, ensure that you cover the connectors when you remove the system from the enclosure. 4. Remove the system cover. After working inside your system Prerequisites Follow the safety guidelines listed in Safety instructions on page 45. Steps 1. Install the system cover. 2. Remove the I/O connector cover. CAUTION: To prevent damage to the I/O connectors, do not touch the connectors or the connector pins. 3. Install the system into the enclosure. 4. Turn on the system. Recommended tools You may need the following items to perform the procedures in this section: • Phillips #1 and #2 screwdrivers • T8 and T30 Torx drivers • Wrist grounding strap • Hex nut driver-5 mm Removing the system from the enclosure Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 45. 2. If installed, remove the front bezel from the PowerEdge VRTX enclosure. 3. Turn off the system. Steps 1. Press the release button on the system handle and simultaneously pull the system handle to unlock the system from the enclosure. CAUTION: To prevent damage to the I/O connectors, do not touch connectors or the connector pins. CAUTION: To protect the I/O connector pins, install the I/O connector covers every time a system is removed from the enclosure. 2. Holding the system handle, slide the system out of the enclosure. NOTE: Ensure that you do not lift the system by using only the system handle. 46 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
3.
Install the I/O connector cover.
CAUTION:
To prevent damage to the I/O connectors, ensure that you cover the connectors when you remove the
system from the enclosure.
4.
Remove the system cover.
After working inside your system
Prerequisites
Follow the safety guidelines listed in
Safety instructions
on page 45.
Steps
1.
Install the system cover.
2.
Remove the I/O connector cover.
CAUTION:
To prevent damage to the I/O connectors, do not touch the connectors or the connector pins.
3.
Install the system into the enclosure.
4.
Turn on the system.
Recommended tools
You may need the following items to perform the procedures in this section:
•
Phillips #1 and #2 screwdrivers
•
T8 and T30 Torx drivers
•
Wrist grounding strap
•
Hex nut driver-5 mm
Removing the system from the enclosure
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 45.
2.
If installed, remove the front bezel from the PowerEdge VRTX enclosure.
3.
Turn off the system.
Steps
1.
Press the release button on the system handle and simultaneously pull the system handle to unlock the system from the enclosure.
CAUTION:
To prevent damage to the I/O connectors, do not touch connectors or the connector pins.
CAUTION:
To protect the I/O connector pins, install the I/O connector covers every time a system is removed from
the enclosure.
2.
Holding the system handle, slide the system out of the enclosure.
NOTE:
Ensure that you do not lift the system by using only the system handle.
46
Installing and removing system components