Dell PowerEdge M640 EMC for VRTX enclosure Installation and Service Manual - Page 71

Removing the processor from the processor and heat sink module

Get Dell PowerEdge M640 PDF manuals and user guides View all Dell PowerEdge M640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Figure 31. Removing the processor and heat sink module Next steps 1. Install the processor into the processor and heat sink module. Removing the processor from the processor and heat sink module Prerequisites WARNING: The heat sink may be hot to touch for some time after the system has been powered down. Allow the heat sink to cool before removing it. 1. Follow the safety guidelines listed in Safety instructions on page 45. 2. Follow the procedure listed in Before working inside your system on page 45. 3. Remove the air shroud. 4. Remove the processor into the processor and heat sink module. Steps 1. Insert a flat blade screwdriver into the release slot marked with a yellow label. Rotate (do not pry) the screwdriver to break the thermal paste seal. 2. Push the retaining clips on the processor bracket to unlock the bracket from the heat sink. Installing and removing system components 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Figure 31. Removing the processor and heat sink module
Next steps
1.
Install the processor into the processor and heat sink module
.
Removing the processor from the processor and heat sink
module
Prerequisites
WARNING:
The heat sink may be hot to touch for some time after the system has been powered down. Allow the heat
sink to cool before removing it.
1.
Follow the safety guidelines listed in
Safety instructions
on page 45.
2.
Follow the procedure listed in
Before working inside your system
on page 45.
3.
Remove the air shroud
.
4.
Remove the processor into the processor and heat sink module
.
Steps
1.
Insert a flat blade screwdriver into the release slot marked with a yellow label. Rotate (do not pry) the screwdriver to break the
thermal paste seal.
2.
Push the retaining clips on the processor bracket to unlock the bracket from the heat sink.
Installing and removing system components
71