Dell PowerEdge M640 EMC for VRTX enclosure Installation and Service Manual - Page 78

Network Daughter Card, Removing the Network Daughter Card

Get Dell PowerEdge M640 PDF manuals and user guides View all Dell PowerEdge M640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Figure 39. Installing the M.2 SSD module a. module connector (2) b. screws (2) c. modules (2) Next steps 1. Install the air shroud. 2. Follow the procedure listed in After working inside your system on page 46. Network Daughter Card Removing the Network Daughter Card Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 45. 2. Follow the procedure listed in Before working inside your system on page 45. 3. Remove the mezzanine card. Steps 1. Using the Phillips #2 screwdriver, remove the two screws that secure the Network Daughter Card (NDC) to the system board. CAUTION: To prevent damage to the NDC, you must hold the card only by its edges. 2. Lift the card from the system board. 78 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Figure 39. Installing the M.2 SSD module
a.
module connector (2)
b.
screws (2)
c.
modules (2)
Next steps
1.
Install the air shroud
.
2.
Follow the procedure listed in
After working inside your system
on page 46.
Network Daughter Card
Removing the Network Daughter Card
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 45.
2.
Follow the procedure listed in
Before working inside your system
on page 45.
3.
Remove the mezzanine card
.
Steps
1.
Using the Phillips #2 screwdriver, remove the two screws that secure the Network Daughter Card (NDC) to the system board.
CAUTION:
To prevent damage to the NDC, you must hold the card only by its edges.
2.
Lift the card from the system board.
78
Installing and removing system components