Dell PowerEdge M640 EMC for VRTX enclosure Installation and Service Manual - Page 90

Installing the optional internal dual SD module

Get Dell PowerEdge M640 PDF manuals and user guides View all Dell PowerEdge M640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Figure 52. Removing the optional IDSDM module Next steps Install the IDSDM Installing the optional internal dual SD module Prerequisites Follow the safety guidelines listed in Safety instructions on page 45. NOTE: You must install either the Internal dual SD module (IDSDM) or the BOSS M.2 card in the same IDSDM/BOSS M.2 connector. NOTE: The procedure to install IDSDM and the BOSS M.2 card is the same. Steps 1. Holding both ends of the IDSDM, insert the IDSDM into the IDSDM/BOSS M.2 connector on the system board. NOTE: For information on the location of the IDSDM/BOSS M.2 connector, see the System board jumpers and connectors section. 2. Push the release tab that secures the IDSDM to the system board, in place. 3. Using the Phillips #2 screwdriver, tighten the retention screw that connects the internal dual SD module (IDSDM) to the system board. 4. Pressing the release latches, lower the drive backplane into the system until it is firmly seated, and the latches engage with the system. 90 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Figure 52. Removing the optional IDSDM module
Next steps
Install the IDSDM
Installing the optional internal dual SD module
Prerequisites
Follow the safety guidelines listed in
Safety instructions
on page 45.
NOTE:
You must install either the Internal dual SD module (IDSDM) or the BOSS M.2 card in the same IDSDM/BOSS
M.2 connector.
NOTE:
The procedure to install IDSDM and the BOSS M.2 card is the same.
Steps
1.
Holding both ends of the IDSDM, insert the IDSDM into the IDSDM/BOSS M.2 connector on the system board.
NOTE:
For information on the location of the IDSDM/BOSS M.2 connector, see the System board jumpers and
connectors section.
2.
Push the release tab that secures the IDSDM to the system board, in place.
3.
Using the Phillips #2 screwdriver, tighten the retention screw that connects the internal dual SD module (IDSDM) to the system
board.
4.
Pressing the release latches, lower the drive backplane into the system until it is firmly seated, and the latches engage with the
system.
90
Installing and removing system components