Dell PowerEdge M640 EMC for VRTX enclosure Installation and Service Manual - Page 89

IDSDM, Removing the optional internal dual SD module

Get Dell PowerEdge M640 PDF manuals and user guides View all Dell PowerEdge M640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

NOTE: Temporarily label each SD card with its corresponding slot before removal. Figure 51. Installing the internal MicroSD card Next steps Follow the procedure listed in After working inside your system on page 46. IDSDM Removing the optional internal dual SD module Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 45. 2. Follow the procedure listed in Before working inside your system on page 45. 3. Install the air shroud. NOTE: The procedure to remove IDSDM and the BOSS M.2 card is the same. Steps 1. Pressing the release latches, lift the drive backplane only until the guide pins on the drive cage disengage from the guides on the drive backplane. 2. Using the Phillips #2 screwdriver, loosen the retention screw that connects the internal dual SD module (IDSDM) to the system board. 3. Lift the release tab that secures the IDSDM to the system board. 4. Holding both ends of the IDSDM, lift the IDSDM out of the IDSDM/BOSS M.2 connector on the system board. Installing and removing system components 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
NOTE:
Temporarily label each SD card with its corresponding slot before removal.
Figure 51. Installing the internal MicroSD card
Next steps
Follow the procedure listed in
After working inside your system
on page 46.
IDSDM
Removing the optional internal dual SD module
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 45.
2.
Follow the procedure listed in
Before working inside your system
on page 45.
3.
Install the air shroud
.
NOTE:
The procedure to remove IDSDM and the BOSS M.2 card is the same.
Steps
1.
Pressing the release latches, lift the drive backplane only until the guide pins on the drive cage disengage from the guides on the drive
backplane.
2.
Using the Phillips #2 screwdriver, loosen the retention screw that connects the internal dual SD module (IDSDM) to the system board.
3.
Lift the release tab that secures the IDSDM to the system board.
4.
Holding both ends of the IDSDM, lift the IDSDM out of the IDSDM/BOSS M.2 connector on the system board.
Installing and removing system components
89