Dell PowerEdge R440 EMC Installation and Service Manual - Page 102

Removing the internal PERC riser, Next steps, Prerequisites, Steps

Get Dell PowerEdge R440 PDF manuals and user guides View all Dell PowerEdge R440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

Figure 68. Installing expansion card into riser 1 Next steps 1. If applicable, connect the cables to the expansion card. 2. Install the expansion card riser 3. If applicable, install the air shroud. 4. Follow the procedure listed in After working inside your system on page 59. 5. Install any device drivers required for the card as described in the documentation for the card. Internal PERC riser Removing the internal PERC riser Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the air shroud. Steps 1. Open the cable guiding latch for easy access. 2. Lower the plunger. 3. Press the cable connector and disconnect the PERC cable from the backplane. 4. Hold the blue touch points and lift the internal PERC riser out of the system. 102 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Figure 68. Installing expansion card into riser 1
Next steps
1.
If applicable, connect the cables to the expansion card.
2.
Install the expansion card riser
3.
If applicable,
install the air shroud.
4.
Follow the procedure listed in
After working inside your system
on page 59.
5.
Install any device drivers required for the card as described in the documentation for the card.
Internal PERC riser
Removing the internal PERC riser
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the air shroud.
Steps
1.
Open the cable guiding latch for easy access.
2.
Lower the plunger.
3.
Press the cable connector and disconnect the PERC cable from the backplane.
4.
Hold the blue touch points and lift the internal PERC riser out of the system.
102
Installing and removing system components