Dell PowerEdge R440 EMC Installation and Service Manual - Page 92

Steps, Next steps, Connecting the cable to internal PERC riser

Get Dell PowerEdge R440 PDF manuals and user guides View all Dell PowerEdge R440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Steps 1. Connect the cable to the internal PERC card. Figure 51. Connecting the cable to internal PERC riser 2. Holding the blue touch points, align the slot on the internal PERC riser to the guide on the system board. 3. Insert the internal riser card's edge connector firmly into the system board connector until the riser is fully seated. 4. Lift the plunger to lock the riser in place. Figure 52. Installing internal PERC riser 5. Connect the cables to the backplane and then route the cables to the cable guiding latch to close the latch. Next steps 1. Install the air shroud. 2. Follow the procedure listed in After working inside your system on page 59. 92 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Steps
1.
Connect the cable to the internal PERC card.
Figure 51. Connecting the cable to internal PERC riser
2.
Holding the blue touch points, align the slot on the internal PERC riser to the guide on the system board.
3.
Insert the internal riser card’s edge connector firmly into the system board connector until the riser is fully seated.
4.
Lift the plunger to lock the riser in place.
Figure 52. Installing internal PERC riser
5.
Connect the cables to the backplane and then route the cables to the cable guiding latch to close the latch.
Next steps
1.
Install the air shroud.
2.
Follow the procedure listed in
After working inside your system
on page 59.
92
Installing and removing system components