Dell PowerEdge R440 EMC Installation and Service Manual - Page 15

Back view of the system

Get Dell PowerEdge R440 PDF manuals and user guides View all Dell PowerEdge R440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Back view of the system The back view displays the features available on the back of the system. Figure 9. Back view of the system with full height riser Table 11. Back view of the system with full height riser Item Ports, panels, or slots Icon Description 1 Serial port 2 iDRAC9 dedicated network NA port Use the serial port to connect a serial device to the system. For more information about the supported serial port, see the Technical specifications section. Use the iDRAC9 dedicated network port to securely access the embedded iDRAC on a separate management network, see the Integrated Dell Remote Access Controller User's Guide at www.dell.com/poweredgemanuals 3 Ethernet ports (2) 4 Full height riser slot N/A 5 Power supply unit (PSU) N/A 6 Power supply unit (PSU) N/A 7 LOM riser ports (2) 8 USB 3.0 port (2) 9 VGA port 10 System status indicator N/A cable port 11 System identification button Use the Ethernet ports to connect Local Area Networks (LANs) to the system. For more information about the supported Ethernet ports, see the Technical specifications section. Use the card slots to connect full-height PCIe expansion cards on full height riser. For more information about the PSU configurations, see the Technical specifications section. For more information about the PSU configurations, see the Technical specifications section. For more information about the PSU configurations, see the Technical specifications section. Use the USB 3.0 port to connect USB devices to the system. These ports are 4-pin, USB 3.0-compliant. Use the VGA port to connect a display to the system. For more information about the supported VGA port, see the Technical specifications section. Enables you to connect the status indicator cable and view system status when the CMA is installed. Press the system ID button: • To locate a particular system within a rack. • To turn the system ID on or off. To reset iDRAC, press and hold the button for more than 15 seconds. NOTE: • To reset iDRAC using system ID, ensure that the system ID button is enabled in the iDRAC setup. • If the system stops responding during POST, press and hold the system ID button (for more than five seconds) to enter the BIOS progress mode. Dell EMC PowerEdge R440 system overview 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Back view of the system
The back view displays the features available on the back of the system.
Figure 9. Back view of the system with full height riser
Table 11. Back view of the system with full height riser
Item
Ports, panels, or slots
Icon
Description
1
Serial port
Use the serial port to connect a serial device to the system. For more
information about the supported serial port, see the
Technical
specifications
section.
2
iDRAC9 dedicated network
port
NA
Use the iDRAC9 dedicated network port to securely access the
embedded iDRAC on a separate management network, see the
Integrated Dell Remote Access Controller User's Guide
at
www.dell.com/poweredgemanuals
3
Ethernet ports (2)
Use the Ethernet ports to connect Local Area Networks (LANs) to the
system. For more information about the supported Ethernet ports, see
the
Technical specifications
section.
4
Full height riser slot
N/A
Use the card slots to connect full-height PCIe expansion cards on full
height riser.
5
Power supply unit (PSU)
N/A
For more information about the PSU configurations, see the
Technical
specifications
section.
6
Power supply unit (PSU)
N/A
For more information about the PSU configurations, see the
Technical
specifications
section.
7
LOM riser ports (2)
For more information about the PSU configurations, see the
Technical
specifications
section.
8
USB 3.0 port (2)
Use the USB 3.0 port to connect USB devices to the system. These
ports are 4-pin, USB 3.0-compliant.
9
VGA port
Use the VGA port to connect a display to the system. For more
information about the supported VGA port, see the
Technical
specifications
section.
10
System status indicator
cable port
N/A
Enables you to connect the status indicator cable and view system
status when the CMA is installed.
11
System identification button
Press the system ID button:
•
To locate a particular system within a rack.
•
To turn the system ID on or off.
To reset iDRAC, press and hold the button for more than 15 seconds.
NOTE:
•
To reset iDRAC using system ID, ensure that the system
ID button is enabled in the iDRAC setup.
•
If the system stops responding during POST, press and
hold the system ID button (for more than five seconds) to
enter the BIOS progress mode.
Dell EMC PowerEdge R440 system overview
15