Dell PowerEdge R440 EMC Installation and Service Manual - Page 131

Removing the right control panel

Get Dell PowerEdge R440 PDF manuals and user guides View all Dell PowerEdge R440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

Figure 107. Installing the cable cover Next steps 1. Follow the safety guidelines listed in Safety instructions. 2. Install the air shroud. 3. Install the internal PERC riser. 4. Follow the procedure listed in Before working inside your system on page 59. Removing the right control panel Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system on page 59. 3. Remove the internal PERC riser. Steps 1. Lift the cable latch and disconnect the control panel cable from the connector on the system board. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. You must route the cables properly when you replace them to prevent the cables from being pinched or crimped. 2. Using a Phillips #1 screwdriver, remove the screws that secure the cable cover to the system. Figure 108. Removing the cable cover 3. Using a Phillips #1 screwdriver, remove the screw that secures the control panel to the system. Installing and removing system components 131

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Figure 107. Installing the cable cover
Next steps
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Install the air shroud.
3.
Install the internal PERC riser.
4.
Follow the procedure listed in
Before working inside your system
on page 59.
Removing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
on page 59.
3.
Remove the internal PERC riser.
Steps
1.
Lift the cable latch and disconnect the control panel cable from the connector on the system board.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. You must route
the cables properly when you replace them to prevent the cables from being pinched or crimped.
2.
Using a Phillips #1 screwdriver, remove the screws that secure the cable cover to the system.
Figure 108. Removing the cable cover
3.
Using a Phillips #1 screwdriver, remove the screw that secures the control panel to the system.
Installing and removing system components
131