Dell PowerEdge R440 EMC Installation and Service Manual - Page 104

Removing the PERC card from the internal PERC riser, Next steps, Prerequisites

Get Dell PowerEdge R440 PDF manuals and user guides View all Dell PowerEdge R440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Figure 71. Connecting the cable to internal PERC riser 2. Holding the blue touch points, align the slot on the internal PERC riser to the guide on the system board. 3. Insert the internal riser card's edge connector firmly into the system board connector until the riser is fully seated. 4. Lift the plunger to lock the riser in place. Figure 72. Installing internal PERC riser 5. Connect the cables to the backplane and then route the cables to the cable guiding latch to close the latch. Next steps 1. Install the air shroud. 2. Follow the procedure listed in After working inside your system on page 59. Removing the PERC card from the internal PERC riser Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the air shroud. 4. Remove the internal PERC riser. 104 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Figure 71. Connecting the cable to internal PERC riser
2.
Holding the blue touch points, align the slot on the internal PERC riser to the guide on the system board.
3.
Insert the internal riser card’s edge connector firmly into the system board connector until the riser is fully seated.
4.
Lift the plunger to lock the riser in place.
Figure 72. Installing internal PERC riser
5.
Connect the cables to the backplane and then route the cables to the cable guiding latch to close the latch.
Next steps
1.
Install the air shroud.
2.
Follow the procedure listed in
After working inside your system
on page 59.
Removing the PERC card from the internal PERC riser
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the air shroud.
4.
Remove the internal PERC riser.
104
Installing and removing system components