Dell PowerEdge R440 EMC Installation and Service Manual - Page 112

LOM riser card, Removing the LOM riser card

Get Dell PowerEdge R440 PDF manuals and user guides View all Dell PowerEdge R440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

Figure 80. Installing optional IDSDM/vFlash card Next steps 1. Install the MicroSD cards. NOTE: Reinstall the MicroSD cards into the same slots based on the labels you had marked on the cards during removal. 2. Follow the procedure listed in After working inside your system on page 59 . LOM riser card Removing the LOM riser card Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system on page 59. 3. If installed, remove the risers. Steps 1. Using a Phillips #2 screwdriver, loosen the screws that secure the LOM riser card to the system board. 2. Release the two blue side plastic snaps holding the LOM riser card. 3. Hold the LOM riser card by the edges on either side, and lift to remove it from the connector on the system board. 4. Slide the LOM riser card towards the front of the system until the Ethernet connectors or the Small form-factor pluggable (SFP) are clear of the slot in the back of the system. 112 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Figure 80. Installing optional IDSDM/vFlash card
Next steps
1.
Install the MicroSD cards
.
NOTE:
Reinstall the MicroSD cards into the same slots based on the labels you had marked on the cards during
removal.
2.
Follow the procedure listed in
After working inside your system
on page 59 .
LOM riser card
Removing the LOM riser card
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
on page 59.
3.
If installed, remove the risers.
Steps
1.
Using a Phillips #2 screwdriver, loosen the screws that secure the LOM riser card to the system board.
2.
Release the two blue side plastic snaps holding the LOM riser card.
3.
Hold the LOM riser card by the edges on either side, and lift to remove it from the connector on the system board.
4.
Slide the LOM riser card towards the front of the system until the Ethernet connectors or the Small form-factor pluggable (SFP) are
clear of the slot in the back of the system.
112
Installing and removing system components