Dell PowerVault DR6000 Owners Manual - Page 57

Removing Expansion-Card Risers, Close the expansion-card latches.

Get Dell PowerVault DR6000 PDF manuals and user guides View all Dell PowerVault DR6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

NOTE: The expansion-card riser 1 can be used only when both the processors are installed. 1. Unpack the expansion card and prepare it for installation. For instructions, see the documentation accompanying the card. 2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and peripherals. 3. Open the system. 4. Remove the expansion-card riser. 5. Press tab A and rotate the latch clockwise. 6. Press tab B and rotate the latch down. 7. Holding the card by its edges, position the card so that the card-edge connector aligns with the expansion-card connector. 8. Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated. 9. Close the expansion-card latches. 10. If applicable, connect any cables to the expansion card. 11. Install the expansion-card riser. 12. Close the system. 13. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. 14. Install any device drivers required for the card as described in the documentation for the card. Removing Expansion-Card Risers CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. NOTE: The expansion-card riser 1 can be used only when both the processors are installed. 1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and peripherals. 2. Open the system. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
NOTE:
The expansion-card riser 1 can be used only when both the processors are installed.
1.
Unpack the expansion card and prepare it for installation.
For instructions, see the documentation accompanying the card.
2.
Turn off the system, including any attached peripherals, and disconnect the system from the
electrical outlet and peripherals.
3.
Open the system.
4.
Remove the expansion-card riser.
5.
Press tab A and rotate the latch clockwise.
6.
Press tab B and rotate the latch down.
7.
Holding the card by its edges, position the card so that the card-edge connector aligns with the
expansion-card connector.
8.
Insert the card-edge connector firmly into the expansion-card connector until the card is fully
seated.
9.
Close the expansion-card latches.
10.
If applicable, connect any cables to the expansion card.
11.
Install the expansion-card riser.
12.
Close the system.
13.
Reconnect the system to its electrical outlet and turn the system on, including any attached
peripherals.
14.
Install any device drivers required for the card as described in the documentation for the card.
Removing Expansion-Card Risers
CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
NOTE:
The expansion-card riser 1 can be used only when both the processors are installed.
1.
Turn off the system, including any attached peripherals, and disconnect the system from the
electrical outlet and peripherals.
2.
Open the system.
57