Dell PowerVault DR6000 Owners Manual - Page 79

I/O Panel, Removing The I/O Panel

Get Dell PowerVault DR6000 PDF manuals and user guides View all Dell PowerVault DR6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

6. Reconnect all the cables to the backplane. 7. Install both the hard drives in their original location. 8. Close the system. 9. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. I/O Panel Removing The I/O Panel CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. If installed, remove the front bezel. 2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and peripherals. 3. Open the system. CAUTION: To prevent damage to the I/O cable, you must release the locking tab before removing or installing the I/O cable from the connector on the hard-drive backplane. 4. Rotate the locking tab on the I/O cable connector clockwise 90 degrees to release the lock. 5. Disconnect the I/O cable from the backplane. 6. Remove the three Torx screws securing the I/O panel to the chassis. 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
6.
Reconnect all the cables to the backplane.
7.
Install both the hard drives in their original location.
8.
Close the system.
9.
Reconnect the system to its electrical outlet and turn the system on, including any attached
peripherals.
I/O Panel
Removing The I/O Panel
CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
1.
If installed, remove the front bezel.
2.
Turn off the system, including any attached peripherals, and disconnect the system from the
electrical outlet and peripherals.
3.
Open the system.
CAUTION: To prevent damage to the I/O cable, you must release the locking tab before
removing or installing the I/O cable from the connector on the hard-drive backplane.
4.
Rotate the locking tab on the I/O cable connector clockwise 90 degrees to release the lock.
5.
Disconnect the I/O cable from the backplane.
6.
Remove the three Torx screws securing the I/O panel to the chassis.
79