Dell PowerVault DR6000 Owners Manual - Page 80

Installing The I/O Panel, Removing and Installing the I/O Panel

Get Dell PowerVault DR6000 PDF manuals and user guides View all Dell PowerVault DR6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

7. Pull out the I/O panel cable through the channel on the chassis. Figure 44. Removing and Installing the I/O Panel 1. I/O panel cable 3. Torx screws (3) 5. chassis 2. hard-drive backplane 4. I/O panel Installing The I/O Panel CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. If installed, remove the front bezel. 2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and peripherals. 3. Open the system. 4. Fold the label around the cable. 5. Push the cable until the cable passes completely through the channel. CAUTION: To prevent damage to the I/O cable, you must release the locking tab before removing or installing the I/O cable from the connector on the hard-drive backplane. 6. If locked, rotate the locking tab on the I/O cable connector clockwise 90 degrees to release the lock. 7. Connect the I/O panel cable to the connector on the hard-drive backplane. 8. Rotate the locking tab on the I/O cable connector counter clockwise 90 degrees to secure the lock. 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
7.
Pull out the I/O panel cable through the channel on the chassis.
Figure 44. Removing and Installing the I/O Panel
1.
I/O panel cable
2.
hard-drive backplane
3.
Torx screws (3)
4.
I/O panel
5.
chassis
Installing The I/O Panel
CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
1.
If installed, remove the front bezel.
2.
Turn off the system, including any attached peripherals, and disconnect the system from the
electrical outlet and peripherals.
3.
Open the system.
4.
Fold the label around the cable.
5.
Push the cable until the cable passes completely through the channel.
CAUTION: To prevent damage to the I/O cable, you must release the locking tab before
removing or installing the I/O cable from the connector on the hard-drive backplane.
6.
If locked, rotate the locking tab on the I/O cable connector clockwise 90 degrees to release the lock.
7.
Connect the I/O panel cable to the connector on the hard-drive backplane.
8.
Rotate the locking tab on the I/O cable connector counter clockwise 90 degrees to secure the lock.
80