Fluke 1586A/2DS Product Manual - Page 122

Table 7-1. Error Messages cont., Error Code, Error Message, Causes and Solutions, Cause, Solution,

Get Fluke 1586A/2DS PDF manuals and user guides View all Fluke 1586A/2DS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 122 highlights

1586A Users Manual Error Code Error 306 Error 307 Error 318 Error 320 Error 322 Error 323 Error 324 Error 325 Error 398 Table 7-1. Error Messages (cont.) Error Message Causes and Solutions Not waiting for reference Cause: CALibrate:NEXT command with a reference value was received, but the reference value is not allowed for current step. Solution: Check the parameter value and try again. Continue command ignored Cause: CALibrate:NEXT command was received, but it is not expected for current calibrate step. Solution: Check the parameter value and try again. Reading does not match reference Cause: The measured value out of range, it might be caused by wrong input signal or hardware defect. Solution: Make sure that the input signal matches the requirement. If the input signal is correct, cycle the power. If the error occurs again, contact Fluke (see Chapter 1). Timeout waiting for reading Cause: Timeout while waiting readings from inguard. Solution: Cycle the power. If the error occurs again, contact Fluke (see Chapter 1). Password missing Cause: CALibrate:ENABle command was received to unlock the calibration but ADMIN password is not provided. Solution: Make sure that ADMIN password was sent with the CALibrate:ENABle command. Wrong password Cause: CALibrate:ENABle command was received to unlock the calibration but the ADMIN password is wrong. Solution: Make sure that correct ADMIN password was sent with the CALibrate:ENABle command. Calibration locked Cause: The calibration is locked when a CALibrate command was received. Solution: Use the CALibrate:ENABle command to unlock the calibration first. Cannot get stable readings Solution 1: Check calibrator and make sure that the correct signal is being outputted from the calibrator. Solution 2: Cycle the power and run calibration again. If the error occurs again, the relay card needs serviced, contact Fluke (see Chapter 1). Anomalous error %d Cause: Unknown error occurred during the calibration procedure. Solution: Restart the calibration procedure. If the error occurs again, contact Fluke (see Chapter 1). 7-8 MyFlukeStore Shop for Fluke products online at: www. .com 1.888.610.7664

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
1586A
Users Manual
7-8
Table 7-1. Error Messages (cont.)
Error Code
Error Message
Causes and Solutions
Error 306
Not waiting for
reference
Cause:
CALibrate:NEXT command with a reference value
was received, but the reference value is not allowed for
current step.
Solution:
Check the parameter value and try again.
Error 307
Continue command
ignored
Cause:
CALibrate:NEXT command was received, but it is not
expected for current calibrate step.
Solution:
Check the parameter value and try again.
Error 318
Reading does not
match reference
Cause:
The measured value out of range, it might be caused
by wrong input signal or hardware defect.
Solution:
Make sure that the input signal matches the
requirement. If the input signal is correct, cycle the power. If
the error occurs again, contact Fluke (see Chapter 1).
Error 320
Timeout waiting for
reading
Cause:
Timeout while waiting readings from inguard.
Solution:
Cycle the power. If the error occurs again, contact
Fluke (see Chapter 1).
Error 322
Password missing
Cause:
CALibrate:ENABle command was received to unlock
the calibration but ADMIN password is not provided.
Solution:
Make sure that ADMIN password was sent with the
CALibrate:ENABle command.
Error 323
Wrong password
Cause:
CALibrate:ENABle command was received to unlock
the calibration but the ADMIN password is wrong.
Solution:
Make sure that correct ADMIN password was sent
with the CALibrate:ENABle command.
Error 324
Calibration locked
Cause:
The calibration is locked when a CALibrate command
was received.
Solution:
Use the CALibrate:ENABle command to unlock the
calibration first.
Error 325
Cannot get stable
readings
Solution 1:
Check calibrator and make sure that the correct
signal is being outputted from the calibrator.
Solution 2:
Cycle the power and run calibration again. If the
error occurs again, the relay card needs serviced, contact
Fluke (see Chapter 1).
Error 398
Anomalous error %d
Cause:
Unknown error occurred during the calibration
procedure.
Solution:
Restart the calibration procedure. If the error
occurs again, contact Fluke (see Chapter 1).
Shop for Fluke products online at:
1.888.610.7664
www.
MyFlukeStore
.com