Fluke 1586A/2DS Product Manual - Page 135

Table 7-2. Troubleshooting Chart cont.

Get Fluke 1586A/2DS PDF manuals and user guides View all Fluke 1586A/2DS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 135 highlights

7 Error Messages and Troubleshooting Troubleshooting Problem Cannot read USB drive. Product does not start to scan after the scan is started. Product does not record when I start a scan. The Product starts with default settings. Product is out of memory. Table 7-2. Troubleshooting Chart (cont.) Causes and Solutions Cause 1: USB drive not installed properly. Solution 1: Make sure the USB drive is fully inserted. The LED light will illuminate in less than 30 seconds. Cause 2: USB driver locked by application (LED lights always illuminated even if USB drive is not installed.) Solution 2: Cycle the power with the main power switch and insert the USB drive again. Cause 3: USB drive not recognized. Solution 3: Replace the USB drive. Cause 4: USB drive inoperative or damaged. Solution 4: Replace USB drive. Cause 1: The Product is waiting to be triggered. Solution 1: Check the trigger type in the test setup and make sure the trigger is properly configured. Cause 1: The Auto Recording feature is not turned on. Solution: Manually push record to start recording or turn on Auto Recording in the test setup. Cause: The SRAM battery is dead. Solution: Contact Fluke. See Chapter 1. Cause: The internal memory or USB drive is out of space. Solution: Delete or transfer some files to free up memory. 7-21 MyFlukeStore Shop for Fluke products online at: www. .com 1.888.610.7664

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Error Messages and Troubleshooting
Troubleshooting
7
7-21
Table 7-2. Troubleshooting Chart (cont.)
Problem
Causes and Solutions
Cannot read USB drive.
Cause 1:
USB drive not installed properly.
Solution 1:
Make sure the USB drive is fully inserted. The LED light will
illuminate in less than 30 seconds.
Cause 2:
USB driver locked by application (LED lights always illuminated even
if USB drive is not installed.)
Solution 2:
Cycle the power with the main power switch and insert the USB
drive again.
Cause 3:
USB drive not recognized.
Solution 3:
Replace the USB drive.
Cause 4:
USB drive inoperative or damaged.
Solution 4:
Replace USB drive.
Product does not start
to scan after the scan is
started.
Cause 1:
The Product is waiting to be triggered.
Solution 1:
Check the trigger type in the test setup and make sure the trigger is
properly configured.
Product does not record
when I start a scan.
Cause 1:
The Auto Recording feature is not turned on.
Solution:
Manually push record to start recording or turn on Auto Recording in
the test setup.
The Product starts with
default settings.
Cause:
The SRAM battery is dead.
Solution:
Contact Fluke. See Chapter 1.
Product is out of
memory.
Cause:
The internal memory or USB drive is out of space.
Solution:
Delete or transfer some files to free up memory.
Shop for Fluke products online at:
1.888.610.7664
www.
MyFlukeStore
.com