Fluke 1586A/2DS Product Manual - Page 95

Con an Automated Test

Get Fluke 1586A/2DS PDF manuals and user guides View all Fluke 1586A/2DS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

4 Scan/Monitor, Record, and Data Automated Test Configure an Automated Test The Automated Test is a trigger type that is configured in the Test Setup menu. The options in the Automated Test setup lets the user set a series of custom temperature setpoints and select a test sequence that the Product will run without user interaction. Refer to Table 4-4 to setup an Automated Test. Table 4-4. Automated Test Setup 1 2 3 4 11 5 6 10 7 9 8 Item    Function hcn070.eps Sets the number of times to repeat a scan sweep at each setpoint. Sets the test sequence. Selections available: Linear - This scan sequence will scan the first reference channel (Ref1), then all of the enabled channels in ascending channel order, followed by the optional second reference channel (Ref2). For example: Ref1 > Ch102 > Ch103 > Ch104 > Ref2. Alternate Reference - This scan sequence will scan the first reference channel (Ref1), then a single channel, followed by the optional second reference channel (Ref2). This then repeats for all the other enabled channels. For example: Ref1> Ch102 > Ref2 > Ref1 > Ch103 > Ref2 > Ref1 > Ch104 > Ref2. Up/Down - This scan sequence will scan the first reference channel (Ref1), then all of the enabled channels in ascending channel order, followed by the optional second reference channel (Ref2). This is then immediately repeated in reverse, descending order. For example: Ref1 > Ch102 > Ch103 > Ch104 > Ref2 > Ref2 > Ch104 > Ch103 > Ch102 > Ref1. Set the reference channels that the reference probes are connected to. The Reference Channel 1 is required, the Reference Channel 2 is optional. 4-17 MyFlukeStore Shop for Fluke products online at: www. .com 1.888.610.7664

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Scan/Monitor, Record, and Data
Automated Test
4
4-17
Configure an Automated Test
The Automated Test is a trigger type that is configured in the Test Setup menu. The
options in the Automated Test setup lets the user set a series of custom temperature
setpoints and select a test sequence that the Product will run without user interaction.
Refer to Table 4-4 to setup an Automated Test.
Table 4-4. Automated Test Setup
1
2
4
6
5
7
8
10
9
11
3
hcn070.eps
Item
Function
Sets the number of times to repeat a scan sweep at each setpoint.
Sets the test sequence. Selections available:
Linear
– This scan sequence will scan the first reference channel (Ref1), then all of the enabled
channels in ascending channel order, followed by the optional second reference channel (Ref2).
For example:
Ref1 > Ch102 > Ch103 > Ch104 > Ref2.
Alternate Reference
– This scan sequence will scan the first reference channel (Ref1), then a
single channel, followed by the optional second reference channel (Ref2). This then repeats for all
the other enabled channels. For example:
Ref1> Ch102 > Ref2 > Ref1 > Ch103 > Ref2 > Ref1 >
Ch104 > Ref2.
Up/Down
– This scan sequence will scan the first reference channel (Ref1), then all of the
enabled channels in ascending channel order, followed by the optional second reference channel
(Ref2). This is then immediately repeated in reverse, descending order. For example:
Ref1 >
Ch102 > Ch103 > Ch104 > Ref2 > Ref2 > Ch104 > Ch103 > Ch102 > Ref1.
Set the reference channels that the reference probes are connected to. The Reference Channel 1
is required, the Reference Channel 2 is optional.
Shop for Fluke products online at:
1.888.610.7664
www.
MyFlukeStore
.com