Fluke 726 FE 726 Users Manual - Page 24

Configuration Menus, Contrast Adjustment

Get Fluke 726 PDF manuals and user guides View all Fluke 726 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

726 Users Manual Configuration Menus Use the configuration menus to set or change these parameters of the Calibrator: • Contrast Adjustment • Shut Down Mode • CJC on/off • °C/°F • Frequency/Pulse output voltage • Pulse output frequency • HART resistor on/off To enter the configuration menus, press C. Press S, to save new configuration. Press G/EXIT CONFIG to exit configuration. Configuration menus are explained below. Contrast Adjustment To adjust the contrast (see Figure 5): 1. Press C until Contst Adjust appears on the display. 2. Use X and W to adjust the contrast up and down. 3. Press S to save the setting. 14 726 PRECISION CALIBRATOR 1 3 %Error V mA LOOP ZERO 3 Seconds OPEN/CLOSE SWITCH TEST MEAS SOURCE HART V mA TC RTD FREQ PULSE CONFIG SELECTION EXIT CONFIG 2 100% SAVE RECALL ENTER TRIGGER/STOP RRReeRtteeuuccrrnnaalllttoo 25% 25% 0% Figure 5. Adjusting the Contrast bec06f.eps

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
726
Users Manual
14
Configuration Menus
Use the configuration menus to set or change these
parameters of the Calibrator:
•
Contrast Adjustment
•
Shut Down Mode
•
CJC on/off
•
°
C/
°
F
•
Frequency/Pulse output voltage
•
Pulse output frequency
•
HART resistor on/off
To enter the configuration menus, press
C
. Press
S
, to save new configuration. Press
G
/
EXIT
CONFIG
to exit configuration.
Configuration menus are explained below.
Contrast Adjustment
To adjust the contrast (see Figure 5):
1.
Press
C
until Contst Adjust appears on the
display.
2.
Use
X
and
W
to adjust the contrast up and down.
3.
Press
S
to save the setting.
726
PRECISION CALIBRATOR
0%
25%
25%
SAVE
RECALL
Return to
Recal
FREQ
MEAS
SOURCE
ENTER
EXIT CONFIG
HART
TC
RTD
PULSE
V
mA
V
mA
LOOP
SWITCH
TEST
100%
%Error
ZERO
3 Seconds
OPEN/CLOSE
TRIGGER/STOP
CONFIG
SELECTION
Return to
Recall
1
2
3
bec06f.eps
Figure 5. Adjusting the Contrast