HP EliteDesk 800 G6 Maintenance and Service Guide - Page 26

Cleaning the mouse, Service considerations, Tools and software requirements, Screws

Get HP EliteDesk 800 G6 PDF manuals and user guides View all HP EliteDesk 800 G6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Cleaning the mouse Use this information to properly clean the mouse. Before cleaning the mouse, be sure that the power to the computer is turned off. ● Clean the mouse ball by first removing the retaining plate and the ball from the housing. Pull out any debris from the ball socket and wipe the ball with a clean, dry cloth before reassembly. ● To clean the mouse body, follow the procedures in Cleaning the computer case on page 15. Service considerations Keep these considerations in mind during the disassembly and assembly of the computer. Tools and software requirements Servicing the computer requires these tools. ● Torx T-15 screwdriver ● Flat-bladed screwdriver (can sometimes be used in place of the Torx screwdriver) ● Phillips P1 screwdriver ● Nonconductive, nonmarking pry tool ● Diagnostics software Screws The screws used in the computer are not interchangeable. They could have standard or metric threads and might be of different lengths. If you use an incorrect screw during the reassembly process, it can damage the unit. HP strongly recommends that you keep all screws that you remove during disassembly with the removed part and then return them to their proper locations. IMPORTANT: As you remove each subassembly from the computer, place it away from the work area to prevent damage. Cables and connectors Use this information properly handle cables. Apply only the tension required to seat or unseat the cables during insertion or removal from the connector. Handle cables by the connector whenever possible. In all cases, avoid bending or twisting the cables, and route the cables so that they cannot be caught or snagged by parts being removed or replaced. IMPORTANT: When servicing this computer, be sure to place cables in their proper location during the reassembly process. Improper cable placement can damage the computer. Hard drives Handle hard drives as delicate, precision components, avoiding all physical shock and vibration. This advice applies to failed drives as well as replacement spares. 16 Chapter 3 Routine care, SATA drive guidelines, and disassembly preparation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Cleaning the mouse
Use this information to properly clean the mouse.
Before cleaning the mouse, be sure that the power to the computer is turned
off.
●
Clean the mouse ball by
first
removing the retaining plate and the ball from the housing. Pull out any
debris from the ball socket and wipe the ball with a clean, dry cloth before reassembly.
●
To clean the mouse body, follow the procedures in
Cleaning the computer case
on page
15
.
Service considerations
Keep these considerations in mind during the disassembly and assembly of the computer.
Tools and software requirements
Servicing the computer requires these tools.
●
Torx T-15 screwdriver
●
Flat-bladed screwdriver (can sometimes be used in place of the Torx screwdriver)
●
Phillips P1 screwdriver
●
Nonconductive, nonmarking pry tool
●
Diagnostics software
Screws
The screws used in the computer are not interchangeable. They could have standard or metric threads and
might be of
different
lengths.
If you use an incorrect screw during the reassembly process, it can damage the unit. HP strongly recommends
that you keep all screws that you remove during disassembly with the removed part and then return them to
their proper locations.
IMPORTANT:
As you remove each subassembly from the computer, place it away from the work area to
prevent damage.
Cables and connectors
Use this information properly handle cables.
Apply only the tension required to seat or unseat the cables during insertion or removal from the connector.
Handle cables by the connector whenever possible. In all cases, avoid bending or twisting the cables, and
route the cables so that they cannot be caught or snagged by parts being removed or replaced.
IMPORTANT:
When servicing this computer, be sure to place cables in their proper location during the
reassembly process. Improper cable placement can damage the computer.
Hard drives
Handle hard drives as delicate, precision components, avoiding all physical shock and vibration. This advice
applies to failed drives as well as replacement spares.
16
Chapter 3
Routine care, SATA drive guidelines, and disassembly preparation