HP EliteDesk 800 G6 Maintenance and Service Guide - Page 59

Power supply

Get HP EliteDesk 800 G6 PDF manuals and user guides View all HP EliteDesk 800 G6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

3. Lift speaker straight up to remove it from the two rubber holders (3). To install the speaker, reverse the removal procedures. Power supply To remove the power supply, use these procedures. Before removing the power supply, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 19). 2. Remove the access panel (Access panel on page 19). 3. Remove the optical drive (Optical drive on page 27). 4. Remove the front bezel (Front bezel on page 20). 5. Rotate the drive cage to the upright position (Drive cage on page 22). Remove the power supply: 1. Disconnect the power supply cables from the following system board connectors: PWRCPU (1) PWRCPU (2) (select products only) PWR (3) PWRCMD (4) 2. Remove the power supply cables from the clips built into the bottom of the chassis (5). 3. Remove the three Torx screws (6) that connect the power supply to the rear of the chassis. Power supply 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
3.
Lift speaker straight up to remove it from the two rubber holders
(3)
.
To install the speaker, reverse the removal procedures.
Power supply
To remove the power supply, use these procedures.
Before removing the power supply, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
19
).
2.
Remove the access panel (
Access panel
on page
19
).
3.
Remove the optical drive (
Optical drive
on page
27
).
4.
Remove the front bezel (
Front bezel
on page
20
).
5.
Rotate the drive cage to the upright position (
Drive cage
on page
22
).
Remove the power supply:
1.
Disconnect the power supply cables from the following system board connectors:
PWRCPU
(1)
PWRCPU
(2)
(select products only)
PWR
(3)
PWRCMD
(4)
2.
Remove the power supply cables from the clips built into the bottom of the chassis
(5)
.
3.
Remove the three Torx screws
(6)
that connect the power supply to the rear of the chassis.
Power supply
49