HP EliteDesk 800 G6 Maintenance and Service Guide - Page 31

Removing bezel blanks, System board connections

Get HP EliteDesk 800 G6 PDF manuals and user guides View all HP EliteDesk 800 G6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Removing bezel blanks To remove the bezel blanks, use these procedures. On some models, there may be bezel blanks covering the optical drive bays. You must remove the bezel blank before installing an optical drive. Before removing the bezel blank, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 19). 2. Remove the access panel (Access panel on page 19). 3. Remove the optical drive (Optical drive on page 27). 4. Remove the front bezel (Front bezel on page 20). Remove the bezel blank: ▲ Press the release tab on the inside of the blank (1), and then rotate the blank off the bezel (2). System board connections Use this illustration and table to determine system board connection locations. Removing bezel blanks 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Removing bezel blanks
To remove the bezel blanks, use these procedures.
On some models, there may be bezel blanks covering the optical drive bays. You must remove the bezel blank
before installing an optical drive.
Before removing the bezel blank, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
19
).
2.
Remove the access panel (
Access panel
on page
19
).
3.
Remove the optical drive (
Optical drive
on page
27
).
4.
Remove the front bezel (
Front bezel
on page
20
).
Remove the bezel blank:
▲
Press the release tab on the inside of the blank
(1)
, and then rotate the blank
off
the bezel
(2)
.
System board connections
Use this illustration and table to determine system board connection locations.
Removing bezel blanks
21