HP Mellanox SX1018 Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed
HP Mellanox SX1018 Manual
View all HP Mellanox SX1018 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Mellanox SX1018 manual content summary:
- HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 1
Mellanox MLNX-OS™ User Manual for SX1018HP Ethernet Managed Blade Switch Rev 1.6.2 Software Ver. 3.3.1000 www.mellanox.com - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 2
A PARTICULAR PURPOSE AND NONINFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES FOR ANY DIRECT, INCLUDING, BUT NOT LIMITED TO, PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 3
Table of Contents Rev 1.6.2 Document Revision History 6 About this Manual 7 Intended Audience 7 Related Documentation 7 Glossary 8 Chapter 1 Introduction 10 1.1 MLNX-OS Features Default Gateway 38 4.2 Software Management 38 4.2.1 Upgrading MLNX-OS Software 38 Mellanox Technologies 3 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 4
5.6 IGMP Snooping 67 5.6.1 Configuring IGMP Snooping 67 5.6.2 Defining a Multicast Router Port on a VLAN 68 5.7 Link Layer Discovery Protocol (LLDP 69 5.7.1 Configuring LLDP 69 5.8 Quality of Service (QoS 70 Mellanox Technologies 4 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 5
5.9.2 ACL Actions 74 Chapter 6 IP Routing 75 6.1 General 75 6.1.1 Interface VLAN 75 6.1.2 Equal Cost Multi-Path Routing (ECMP 75 6.1.3 Creating an IP Interface 76 Rev 1.6.2 Mellanox Technologies 5 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 6
System Profile chapter with VPI single switch option Updated downgrade section. Break-out Cables chapter was updated SNMP chapter updated Added LLDP chapter Initial document Mellanox Technologies 6 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 7
Guide System Hardware User Manual Switch Hardware Errata MLNX-OS Command Reference Guide Description The InfiniBand Architecture Specification that is provided by IBTA. Each Mellanox see the switch support product page. This requires a customer support login. Command Reference Guide for MLNX-OS - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 8
). Authorization - grants or refuses privileges to a user/client for accessing specific services. Accounting - tracks network resources consumption by users. Address Resolution Protocol. A network technologies and most IEEE 802 network technologies including Ethernet. Mellanox Technologies 8 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 9
classes of service on the Ethernet link. Remote Authentication Dial In User Service. A networking for computers to connect and use a network service. Accessing memory in a remote side without centralized servers. TACACS+ provides separate AAA services. Extensible Markup Language Gateway. Provides an - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 10
both Ethernet and InfiniBand technology providing the user with greater flexibility. MLNX-OS provides a full suite of management options, including support for Mellanox's Unified Fabric Manager® (UFM), SNMP V1,2,3, and web user interface. In addition, it incorporates a familiar industry-standard CLI - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 11
Table 5 - Ethernet Features Feature Ethernet support IP routing Description • 48K Unicast MAC addresses • VLAN (802.1Q) - 4K • LAG/LACP (802.3ad), ) • VLAN interface • ECMP • BGP • OSPF • PIM • IGMP • VRRP Figure 1: Managing an Ethernet Fabric using MLNX-OS Rev 1.6.2 Mellanox Technologies 11 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 12
installed and powered on your switch according to the instructions in the Hardware Installation Guide, which was shipped with the product. 2.1 Configuration by DHCP (Sheet 1 of 3) Wizard Session Display (Example) Mellanox configuration wizard Do you want to use the wizard for initial configuration? - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 13
the machine, please type a password and then press . Then confirm the password by re-entering it. Note that password characters are not printed. Rev 1.6.2 Mellanox Technologies 13 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 14
saved. To return to the wizard from the CLI, enter the "configuration jump-start" command from configuration mode. Launching CLI... [standalone: master] > Rev 1.6.2 Mellanox Technologies 14 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 15
Table 8 - Configuration Wizard Session - IP Zeroconf Configuration Wizard Session Display - IP Zeroconf Configuration (Example) Mellanox configuration wizard Do you want to use the wizard for initial configuration? y Step 1: Hostname? [switch-112126] Step 2: Use DHCP on mgmt0 interface? [no] Step 3: - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 16
Table 9 - Configuration Wizard Session - Static IP Configuration Wizard Session Display - Static IP Configuration (Example) Mellanox configuration wizard Do you want to use the wizard for initial configuration? y Step 1: Hostname? [switch-112126] Step 2: Use DHCP on mgmt0 interface? [yes] n Step 3: - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 17
jump-start 2.2 Starting The Command Line (CLI) Step 1. Set up an Ethernet connection between the switch and a local network machine using a standard RJ-45 connector. Mellanox Technologies 17 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 18
11:24:13 2011 from 192.168.10.1 Mellanox Switch Step 3. Step 4. switch > Login to the switch (default username is admin, password admin) Once you get the prompt, you are ready to use the system. Refer to MLNX-OS Command Reference Guide for additional information on the CLI commands. 2.3 Starting - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 19
Figure 2: MLNX-OS Login Window Rev 1.6.2 After you log in to MLNX-OS, a (default) status summary window will be displayed containing the following information: Figure 3: Display After Login Mellanox Technologies 19 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 20
admin and change to Config mode. switch > enable switch # config terminal Step 2. Install the license using the key. Run: switch (config) # license install Mellanox Technologies 20 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 21
via CLI: Step 1. Log in as admin. Step 2. Click the Setup tab and then Licensing in the left side navigation pane. Figure 4: No Licenses Installed Mellanox Technologies 21 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 22
in the text box and click "Add Licenses" to install it. Figure 5: Enter Licence Key(s) in Text Box All installed licenses should now be displayed. Mellanox Technologies 22 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 23
at the next system boot. 2.4.3 Retrieving Your Lost License Key If you have lost the MLNX-OS license key, contact your authorized Mellanox reseller and provide the switch's chassis serial number. To obtain the switch's chassis serial number: Step 1. Login to the switch. Step 2. Retrieve - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 24
Rev 1.6.2 Step 3. Step 4. Send your Mellanox reseller the following information to obtain the license key: • The chassis serial number • The type of license you need page 20. Once you receive the license key, you can install the license as described in the sections above. Mellanox Technologies 24 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 25
directly via the console port on the front panel (if it exists). Refer to the MLNX-OS Command Reference Guide for complete set of commands, syntax and examples. 3.1.1 CLI Modes The CLI can be in one of Several commands such as "show" can be applied within any context. Mellanox Technologies 25 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 26
passive Do not type the angled or square brackets, vertical bar, or braces in command lines. This guide uses these symbols only to show the types of entries. CLI commands and options are in lowercase certain configuration options Display system configuration or statistics Mellanox Technologies 26 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 27
can also enter "help" to view a description of the interactive help system. Note also that the CLI supports command and/or parameter tab-completions and their shortened forms. For example, you can enter "en" instead mode) (Exit Enable mode) (You are back in Standard mode) Mellanox Technologies 27 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 28
-logout after 15 minutes switch (config) # cli session auto-logout 15 // 5. Display the final CLI session options switch (config) # show cli CLI current session settings: Mellanox Technologies 28 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 29
Parameter Description A domain name, e.g. "mellanox.com". A hostname, e.g. "switch-1". An interface name, e.g. "mgmt0", "mgmt1 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 30
generating web pages which can be viewed by the user using a web browser. The following web browsers are supported • Internet Explorer 8.0 or higher • Chrome 18 or higher • Mozilla Firefox 12 or higher • Safari menus. Click the "Save" button to the right of "Save Changes?". Mellanox Technologies 30 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 31
or display static and dynamic name servers. Used to edit the login messages: Message of the Day (MOTD), Remote Login message, and Local Login message. Mellanox Technologies 31 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 32
power capacity, and the power available. Displays the installed MLNX-OS images (and the active partition), to upload a new image, and to install a new image. Mellanox Technologies 32 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 33
generate host keys. Used to configure AAA (Authentication, Authorization, and Accounting) security services such as authentication methods and authorization. Used to manage login attempts Used to Provides the ability to manage phy profiles. Manages the link protocol type Mellanox Technologies 33 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 34
display a list of the recent health alerts and enables the user to configure health settings. 3.2.6 IB SM Mgmt The IB SM MGMT menu is not supported in Ethernet systems. Mellanox Technologies 34 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 35
(enabling SM, priority level, and restoring initial configuration). Used to configure security and GUID based prefixes (m_key, sm_key, sa_key, etc), and to manage special SM attributes that about all identified InfiniBand systems in the fabric (adapters, switches, etc). Mellanox Technologies 35 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 36
to HCA, etc) and by the link rate (speed or width). Allows the mapping of System Names to GUIDs to ease system identification. 3.2.8 ETH Mgmt The Eth Mgmt menu is not applicable when the switch profile is not in the switch. Used for managing Access Control in the switch. Mellanox Technologies 36 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 37
(config) # interface ip address For further definitions of the interface, please refer to Mellanox MLNX-OS™ Command Reference Guide. 4.1.2 Configuring IPv6 Address on the Management Interface Step 1. Enable IPv6 on this interface. switch (config) # interface mgmt0 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 38
Switch Mellanox configuration wizard Do you want to use the wizard for initial configuration? yes Step 1: Hostname? [switch-6287a4] Step 2: Use DHCP on mgmt0 interface? [yes] no # In such case the serial connection should be used. 4.1.4 Default Gateway In order to configure manually - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 39
1: SX 2011-04-28 16:02:50 Partition 2: SX 2011-04-28 16:52:50 Last boot partition: 1 Next boot partition: 1 Mellanox Technologies 39 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 40
running reload to run the new image. switch (config) # reload Configuration has been modified; save first? [yes] yes Configuration changes saved. Rebooting... switch (config)# Rev 1.6.2 Mellanox Technologies 40 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 41
-HA 2011-04-10 12:02:49 ppc Last boot partition: 1 Next boot partition: 1 Boot manager password is set. No image install currently in progress. Mellanox Technologies 41 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 42
# For further information, please refer to Mellanox MLNX-OS Command Reference Guide. 4.2.3 Downgrading MLNX-OS Software Prior to 2. Download the requested MLNX-OS version from the following link: http://support.mellanox.com/SupportWeb/ Step 3. Enter your username and password when prompted. - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 43
available to be installed: new_image.img 2010-09-19 16:52:50 Installed images: Partition 1: 2010-09-19 03:46:25 Mellanox Technologies 43 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 44
to the older software version, in these cases above, follow the steps below. Step 1. Run the command: switch (config)# no boot next fallback-reboot enable Mellanox Technologies 44 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 45
FW . If you detect a firmware version mismatch for one or more modules of the switch system, please contact your assigned Mellanox Technologies field application engineer. 4.2.4.2 Importing Firmware and Changing the Default Firmware To perform an automatic firmware update by MLNX-OS for - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 46
-switch To save the configuration to a user-specified file and make the new file the active configuration file, run: switch (config) # configuration write to myconf Mellanox Technologies 46 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 47
switch (config) # show configuration files initial myconf (active) switch (config) # For further information, please refer to Mellanox MLNX-OS Command Reference Guide. 4.3.2 Loading a Configuration File By default, or after a system reset, the system loads the default "initial" configuration file - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 48
basis. Run: switch (config) # logging trap override class For further information, please refer to Mellanox MLNX-OS Command Reference Guide. 4.5 Event Notifications 4.5.1 E-mail Notifications To configure MLNX-OS to send you emails for all configured events and failures - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 49
managing the MLNX-OS switch. The MLNX-OS switch supports Remote Access Dial-In User Service (RADIUS) or Terminal Access Controller Access Control device Plus User Service (RADIUS) protocol. For information on the AAA commands, please refer to Mellanox MLNX-OS Command Reference Guide. Mellanox - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 50
• Supports inbound authentication, outbound authentication and change password request for the authentication service • Provides some level of protection against an active attacker For information on the TACACS+ commands, please refer to Mellanox MLNX-OS Command Reference Guide. 4.7.1.3 LDAP - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 51
Rev 1.6.2 For information on the LDAP commands, please refer to Mellanox MLNX-OS Command Reference Guide. 4.7.2 Secure Shell (SSH) 4.7.2.1 Adding a Host and Providing an SSH Key To (Accounts) and Default Passwords User Role admin monitor Default Password admin monitor Mellanox Technologies 51 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 52
and the monitoring of network devices and their functions. SNMP supports asynchronous event (trap) notifications and queries. MLNX-OS supports: • SNMP versions v1, v2c and v3 • SNMP trap notifications • Standard MIBs • Mellanox private MIBs 4.8.1.1 Standard MIBs Table 23 - Standard MIBs - Textual - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 53
RFC 4318 Comments ifXTable only supported. FAN and Temperature sensors FAN and Temperature states dot1dTpFdbGroup and dot1dStaticGroup are not supported in this MIB, it is supported as a part of MIB is not relevant to InfiniBand. This MIB is not relevant to InfiniBand. Mellanox Technologies 53 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 54
Comments This MIB is not relevant to InfiniBand. 4.8.1.2 Private MIB Table 26 - Private MIBs Supported MIB MELLANOX-SMI-MIB MELLANOX-PRODUCTS-MIB MELLANOX-IF-VPI-MIB MELLANOX-EFM-MIB Comments Mellanox Private MIB main structure (no objects) List of OID - per managed system (sysObjID) IfTable - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 55
host may have different attributes. Run: switch (config) # snmp-server host 10.134.47.3 traps version 3 user my-username auth sha my-password switch (config) # Mellanox Technologies 55 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 56
gateway provides an XML request-response protocol that can be used by end-user tools to get and set management information on the appliance. The service can be accessed over HTTP or HTTPS, and then it uses the existing web authentication mechanism. It can also be accessed over - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 57
Rev 1.6.2 SSH, and then it uses the existing CLI authentication mechanism. XML Gateway - Management information base. For further information please contact Mellanox support. Mellanox Technologies 57 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 58
- user defined string • Module-type - the type of the module plugged in the interface 5.1.1 Break-Out Cables The Break-out Cable is a unique Mellanox capability, where a single physical 40Gbps port is divided into 2x10Gbps or 4x10Gbps ports. It maximizes the flexibility of the end user to use the - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 59
2 10Gb/s SFP+ This port is unmapped by the neighboring split 4 port The maximum number of 10 Gb/s Ethernet ports configurable with this switch is 34. Mellanox Technologies 59 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 60
beware that splitting a port into 4 prevents you from accessing the splittable port, and additional one. For example, in the procedure above, ports 3and 4 become unaccessible. Mellanox Technologies 60 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 61
. 5.2.1 Configuring Static Link Aggregation Group (LAG) To configure a static LAG: Step 1. Log in as admin. Step 2. Enter config mode. Run: switch > enable switch # configure terminal Mellanox Technologies 61 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 62
identified by a tag added to all Ethernet frames running within the domain. This tag is called a VLAN ID (VID) and can take a value of 1-4094. Mellanox Technologies 62 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 63
them a default configured VLAN (Port VLAN ID). On egress, traffic sent from the access port is untagged. • Access-dcb - This mode is Mellanox specific that receives ingress untagged traffic but sends egress priority tag (VLAN ID = 0) • Hybrid - Hybrid port is a port connected to either switches - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 64
context, configure the interface mode to Trunk. Run: switch [standalone: master] (config interface ethernet 1/35) # switchport mode trunk switch [standalone: master] (config interface ethernet 1/35) # Mellanox Technologies 64 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 65
address> vlan interface ethernet / . switch (config) # mac-address-table static unicast 00:11:22:33:44:55 vlan 1 interface ethernet 0/1 Mellanox Technologies 65 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 66
conforms to IEEE standard 802.1D 2004. 5.5.2 RSTP Enhancements RSTP enhancement is a set of functions added to increase the volume of RSTP in Mellanox switches. It adds a set of capabilities related to the behavior of ports in different segments of the network. For example: the required behavior - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 67
sent from the network router by dispatching a join report. A given port can be either manually configured to be a router-port or it can be dynamically manifested when having received a query on a VLAN. Run: switch (config) # vlan 2 switch (config vlan 2) # ip igmp snooping Mellanox Technologies 67 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 68
of the port (the interface is member of VLAN 1 by default). Run: switch (config) # interface ethernet 1/36 switch (config interface ethernet 1/36) # switchport mode hybrid Mellanox Technologies 68 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 69
Enabled Local global configuration Chassis sub type: macAddress (4) Chassis id: 00:11:22:33:44:55 System Name: "switch-111111" System Description: my-system-description Supported capabilities: B Supported capabilities enabled: B Mellanox Technologies 69 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 70
remote-system-description Remote system capabilities supported: B ; B 5.8 Quality of Service (QoS) 5.8.1 Priority Flow Control or datapath. These trace logs are a useful aid in troubleshooting. • Allows the administrator to configure the minimum and maximum PFC globally: Mellanox Technologies 70 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 71
) # switch (config) # interface ethernet 1/1 switch (config interface ethernet 1/1) # Step 6. Enable PFC for the specific interface: switch (config interface ethernet 1/1) # dcb priority-flow-control mode on Mellanox Technologies 71 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 72
is equal 25% per TC. Changing the WRR bandwidth rate will cause a change in the distribution function, for example if you wish to schedule more Mellanox Technologies 72 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 73
is applied. The rule fields represent flow characteristics such as source and destination addresses, protocol and VLAN ID. ACL support currently allows actions of permit or deny rules, and supports only ingress direction. ACL search pattern can be taken from either L2 or L3 fields, e.g L2/L3 source - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 74
access-list my-list)# exit Bind an access-list to a port: Switch (config)# interface ethernet 1/1 Switch (config interface ethernet 1/1)# mac port access-group my-list Mellanox Technologies 74 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 75
router peer networks. Router R1 routing table for 10.0.40/24 will contain the following routes: • 10.0.10.2 • 10.0.20.2 • 10.0.30.2 Figure 10: ECMP Mellanox Technologies 75 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 76
asymmetric hash functions, bidirectional traffic can follow different paths in both directions. The following load balancing types are supported: • Source IP & Port - source IP (SIP) and source UDP/TCP port: If the packet (config interface vlan)#ip address 10.10.10.10 /24 Mellanox Technologies 76 - HP Mellanox SX1018 | Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 77
: 10.10.10.10/24 Broadcast address: 10.10.10.255 MTU: 1500 bytes Description: my-ip-interface Counters: disabled switch (config interface vlan)# Rev 1.6.2 Mellanox Technologies 77
www.mellanox.com
Mellanox MLNX-OS™ User Manual
for
SX1018HP Ethernet Managed Blade Switch
Rev 1.6.2
Software Ver. 3.3.1000