HP Mellanox SX1018 Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 69

Link Layer Discovery Protocol LLDP

Get HP Mellanox SX1018 PDF manuals and user guides View all HP Mellanox SX1018 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Rev 1.6.2 Step 7. Step 8. Step 9. Attach the VLAN to the port's interface. Run: switch (config interface ethernet 1/36) # switchport mode hybrid allowed-vlan 200 switch (config interface ethernet 1/36) # Change to config mode again. Run: switch (config interface ethernet 1/36) # exit switch (config) # Define the MRouter port on the VLAN. Run: switch (config) # vlan 200 switch (config vlan 200) # ip igmp mrouter interface ethernet 1/36 switch (config vlan 200) # 5.7 Link Layer Discovery Protocol (LLDP) The Link Layer Discovery Protocol (LLDP) is a vendor-neutral Link Layer protocol in the Internet Protocol Suite used by network devices for advertising their identity, capabilities, and neighbors on a IEEE 802 LAN. The protocol is formally defined in IEEE 802.1AB. 5.7.1 Configuring LLDP  To configure the LLDP on the switch: Step 1. Log in as admin. Step 2. Enter config mode. Run: switch > enable switch # configure terminal Step 3. Enable LLDP globally on the switch. Run: switch (config) # lldp switch (config) # Step 4. Enable LLDP per interface. Run: switch (config interface ethernet 1/1) # lldp receive switch (config interface ethernet 1/1) # lldp transmit Step 5. Show LLDP local information. Run: switch (config) # show lldp local LLDP is Enabled Local global configuration Chassis sub type: macAddress (4) Chassis id: 00:11:22:33:44:55 System Name: "switch-111111" System Description: my-system-description Supported capabilities: B Supported capabilities enabled: B Mellanox Technologies 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Rev 1.6.2
Mellanox Technologies
69
Step 7.
Attach the VLAN to the port’s interface. Run:
Step 8.
Change to config mode again. Run:
Step 9.
Define the MRouter port on the VLAN. Run:
5.7
Link Layer Discovery Protocol (LLDP)
The Link Layer Discovery Protocol (LLDP) is a vendor-neutral Link Layer protocol in the Inter-
net Protocol Suite used by network devices for advertising their identity, capabilities, and neigh-
bors on a IEEE 802 LAN. The protocol is formally defined in IEEE 802.1AB.
5.7.1
Configuring LLDP
To configure the LLDP on the switch:
Step 1.
Log in as admin.
Step 2.
Enter config mode. Run:
Step 3.
Enable LLDP globally on the switch. Run:
Step 4.
Enable LLDP per interface. Run:
Step 5.
Show LLDP local information. Run:
switch (config interface ethernet 1/36) # switchport mode hybrid allowed-vlan 200
switch (config interface ethernet 1/36) #
switch (config interface ethernet 1/36) # exit
switch (config) #
switch (config) # vlan 200
switch (config vlan 200) # ip igmp mrouter interface ethernet 1/36
switch (config vlan 200) #
switch > enable
switch # configure terminal
switch (config) # lldp
switch (config) #
switch (config interface ethernet 1/1) # lldp receive
switch (config interface ethernet 1/1) # lldp transmit
switch (config) # show lldp local
LLDP is Enabled
Local global configuration
Chassis sub type: macAddress (4)
Chassis id: 00:11:22:33:44:55
System Name: "switch-111111"
System Description: my-system-description
Supported capabilities: B
Supported capabilities enabled: B