HP Mellanox SX1018 Mellanox MLNX-OS User Manual for SX1018HP Ethernet Managed - Page 68

Defining a Multicast Router Port on a VLAN

Get HP Mellanox SX1018 PDF manuals and user guides View all HP Mellanox SX1018 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Rev 1.6.2 5.6.2 Defining a Multicast Router Port on a VLAN You can define a Multicast Router (MRouter) port on a VLAN in one of the following methods:  To change the Interface Switchport to Trunk: Step 1. Log in as admin. Step 2. Enter config mode. Run: switch > enable switch # configure terminal Step 3. Enable IGMP snooping globally. Run: switch (config) # ip igmp snooping switch (config) # Step 4. Change the interface switchport mode of the port (the interface is member of VLAN 1 by default). Run: switch (config) # interface ethernet 1/1 switch (config interface ethernet 1/1) # switchport mode trunk Step 5. Change back to config mode. Run: switch (config interface ethernet 1/1) # exit switch (config) # Step 6. Define the MRouter port on the VLAN. Run: switch (config) # vlan 2 switch (config vlan 2) # ip igmp mrouter interface ethernet 1/1 switch (config vlan 2) #  To change the Interface Switchport to Hybrid: Step 1. Log in as admin. Step 2. Enter config mode. Run: switch > enable switch # configure terminal Step 3. Enable IGMP snooping globally. Run: switch (config) # ip igmp snooping switch (config) # Step 4. Create a VLAN. Run: switch (config) # vlan 200 switch (config vlan 200) # Step 5. Change back to config mode. Run: switch (config vlan 200) # exit switch (config) # Step 6. Change the interface switchport mode of the port (the interface is member of VLAN 1 by default). Run: switch (config) # interface ethernet 1/36 switch (config interface ethernet 1/36) # switchport mode hybrid Mellanox Technologies 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Rev 1.6.2
Mellanox Technologies
68
5.6.2
Defining a Multicast Router Port on a VLAN
You can define a Multicast Router (MRouter) port on a VLAN in one of the following methods:
To change the Interface Switchport to Trunk:
Step 1.
Log in as admin.
Step 2.
Enter config mode. Run:
Step 3.
Enable IGMP snooping globally. Run:
Step 4.
Change the interface switchport mode of the port (the interface is member of VLAN 1 by
default). Run:
Step 5.
Change back to config mode. Run:
Step 6.
Define the MRouter port on the VLAN. Run:
To change the Interface Switchport to Hybrid:
Step 1.
Log in as admin.
Step 2.
Enter config mode. Run:
Step 3.
Enable IGMP snooping globally. Run:
Step 4.
Create a VLAN. Run:
Step 5.
Change back to config mode. Run:
Step 6.
Change the interface switchport mode of the port (the interface is member of VLAN 1 by
default). Run:
switch > enable
switch # configure terminal
switch (config) # ip igmp snooping
switch (config) #
switch (config) # interface ethernet 1/1
switch (config interface ethernet 1/1) # switchport mode trunk
switch (config interface ethernet 1/1) # exit
switch (config) #
switch (config) # vlan 2
switch (config vlan 2) # ip igmp mrouter interface ethernet 1/1
switch (config vlan 2) #
switch > enable
switch # configure terminal
switch (config) # ip igmp snooping
switch (config) #
switch (config) # vlan 200
switch (config vlan 200) #
switch (config vlan 200) # exit
switch (config) #
switch (config) # interface ethernet 1/36
switch (config interface ethernet 1/36) # switchport mode hybrid