HP Model 712/100 hp 9000 series 700 model 712 service handbook (a2615-90039) - Page 116

the A2657A /C2963/64A Hard Disk Drive.

Get HP Model 712/100 - Workstation PDF manuals and user guides View all HP Model 712/100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

6. Remove the plunger. Pull the plunger straight out until it disengages from the power board switch. Slide the plunger from the chassis. 7. Remove the power board. Lift the front of the power board, then pull it toward the front of the unit until it disengages from the grounding clip. WARNING: Use only power supply Model ETYHP127MM with the A2657A /C2963/64A Hard Disk Drive. 8. Remove the bottom HP PAC. 9. Remove the SCSI ribbon cable. From the back of the unit, use a small flat-blade screwdriver to remove the four screws that hold the SCSI ribbon cable connectors in place. 5-40 Field Replaceable Units

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
5–40
Field Replaceable Units
6.
Remove the plunger.
Pull the plunger straight out until it disengages from the power board switch.
Slide the plunger from the chassis.
7.
Remove the power board.
Lift the front of the power board, then pull it toward the front of the unit until it
disengages from the grounding clip.
WARNING:
Use only power supply Model ETYHP127MM with
the A2657A /C2963/64A Hard Disk Drive.
8.
Remove the bottom HP PAC.
9.
Remove the SCSI ribbon cable.
From the back of the unit, use a small flat–blade screwdriver to remove the four
screws that hold the SCSI ribbon cable connectors in place.