HP Model 712/100 hp 9000 series 700 model 712 service handbook (a2615-90039) - Page 41

Configuration

Get HP Model 712/100 - Workstation PDF manuals and user guides View all HP Model 712/100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Configuration 3 This chapter provides details about setting up and changing the system configuration. Workstation Configurations Refer to the HP Apollo 9000 Series 700 Configuration Guide for a complete list of supported accessories, peripherals, and operating systems for the Model 712 workstation. FRU Configurations This section provides information for setting up or changing the configuration of the system Field Replaceable Units (FRUs). Mass Storage Configurations Table 3-1 lists the recommended SCSI IDs for some Model 712 internal and external storage devices. Figure 3-1 through Figure 3-11 show the SCSI ID settings for the Model 712 internal hard disk, and the external C2943A CD-ROM, C2963/4A hard disk, and C2954A DDS Tape mass storage devices. Figure 3-12 shows the jumper configuration for the floppy drive, which is not a SCSI device. NOTICES: The SCSI terminators must be removed from all internal SCSI devices. An external terminator is not required on the system unit if there are no external devices attached. These SCSI IDs are the recommended IDs for each storage device. If an existing device already uses an ID, select an alternate ID. Table 3-1. Default SCSI IDs Internal System Drives: Hard Disk Drive: ID 6 External Drives: C2943A CD-ROM Drive: ID 2 C1530B DDS Tape Drive: ID 3 C2963/4A Hard Disk Drive: ID 5 Configuration 3-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Configuration
3–1
Configuration
3
This chapter provides details about setting up and changing the system configuration.
Workstation Configurations
Refer to the
HP Apollo 9000 Series 700 Configuration Guide
for a complete list of
supported accessories, peripherals, and operating systems for the Model 712 worksta-
tion.
FRU Configurations
This section provides information for setting up or changing the configuration of the
system Field Replaceable Units (FRUs).
Mass Storage Configurations
Table 3–1 lists the recommended SCSI IDs for some Model 712 internal and external
storage devices. Figure 3–1 through Figure 3–11 show the SCSI ID settings for the
Model 712 internal hard disk, and the external C2943A CD–ROM, C2963/4A hard
disk, and C2954A DDS Tape mass storage devices. Figure 3–12 shows the jumper
configuration for the floppy drive, which is not a SCSI device.
NOTICES:
The SCSI terminators must be removed from all in-
ternal SCSI devices. An external terminator is not
required on the system unit if there are no external
devices attached.
These SCSI IDs are the recommended IDs for each
storage device. If an existing device already uses an
ID, select an alternate ID.
Table 3-1.
Default
SCSI IDs
Internal System Drives:
External Drives:
C2943A CD–ROM Drive:
ID 2
C1530B DDS Tape Drive:
ID 3
C2963/4A Hard Disk Drive:
ID 5
Hard Disk Drive:
ID 6