HP Model 712/100 hp 9000 series 700 model 712 service handbook (a2615-90039) - Page 119

Removing the Fan/LED Assembly C1530B/C2954A Tape Drive

Get HP Model 712/100 - Workstation PDF manuals and user guides View all HP Model 712/100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

4. Remove the Fan/LED assembly. Squeeze the clip on the side of the Fan/LED assembly cable connector to disconnect it from the power supply. From the front of the unit, push in the LED until it disengages from the chassis. Tilt the top of the fan toward the front of the unit until it disengages from the mounting pins, then remove the Fan/LED assembly, as shown in Figure 5-29. NOTICE: When replacing the fan, make sure that the arrow on its side points toward the rear of the unit. Figure 6-29. Removing the Fan/LED Assembly (C1530B/C2954A Tape Drive) 5. Remove the power button. Pull the power button straight off the end of the plunger. 6. Remove the plunger. Pull the plunger straight out until it disengages from the power board switch. Slide the plunger from the chassis. Field Replaceable Units 5-43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Field Replaceable Units
5–43
4.
Remove the Fan/LED assembly.
Squeeze the clip on the side of the Fan/LED assembly cable connector to discon-
nect it from the power supply.
From the front of the unit, push in the LED until it disengages from the chassis.
Tilt the top of the fan toward the front of the unit until it disengages from the
mounting pins, then remove the Fan/LED assembly, as shown in Figure 5–29.
NOTICE:
When replacing the fan, make sure that the arrow on
its side points toward the rear of the unit.
Figure 6–29.
Removing the Fan/LED Assembly (C1530B/C2954A Tape Drive)
5.
Remove the power button.
Pull the power button straight off the end of the plunger.
6.
Remove the plunger.
Pull the plunger straight out until it disengages from the power board switch.
Slide the plunger from the chassis.