HP StorageWorks 2/64 HP StorageWorks Core Switch 2/64 Getting Started & Ge - Page 46

Step 5b, Connect the active CP card by Ethernet cable to the LAN by completing

Get HP StorageWorks 2/64 - Core Switch PDF manuals and user guides View all HP StorageWorks 2/64 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

b. Enter the requested information for this IP address at the prompts: Ethernet IP Address [10.77.77.77]: Ethernet Subnetmask [0.0.0.0]: Fibre Channel IP Address [none]: Fibre Channel Subnet Mask [none]: The logical IP address is automatically updated immediately. c. To configure the IP address for logical switch 1, enter the following command at the prompt: ipAddrSet 1 d. Enter the requested information for this IP address at the prompts as described in Step 5b. e. Reboot the CP card by entering the following command at the prompt: reboot Note The terminal serial port can be used to monitor error messages through a serial connection. HP does not recommend using a serial interface during normal operations. Use of a telnet session is recommended instead. f. Remove the serial cable and protect the port from dust by replacing the shipping cap. 6. Connect the active CP card by Ethernet cable to the LAN by completing the following steps: a. Remove the shipping plug from the Ethernet port on the active CP card. b. Insert one end of an Ethernet cable into the Ethernet port. c. Connect the other end to an Ethernet 10/100 Base-T LAN. 7. Repeat Step 6 to connect the standby CP card. 8. Log in to either of the logical switches by telnet using the administrative login. The default administrative login name is admin and the default password is password. 38 getting started and general reference guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
38
getting started and general reference guide
b.
Enter the requested information for this IP address at the prompts:
Ethernet IP Address [10.77.77.77]:
Ethernet Subnetmask [0.0.0.0]:
Fibre Channel IP Address [none]:
Fibre Channel Subnet Mask [none]:
The logical IP address is automatically updated immediately.
c.
To configure the IP address for logical switch 1, enter the following
command at the prompt:
ipAddrSet 1
d.
Enter the requested information for this IP address at the prompts as
described in
Step 5b
.
e.
Reboot the CP card by entering the following command at the prompt:
reboot
Note
The terminal serial port can be used to monitor error messages
through a serial connection. HP does not recommend using a serial
interface during normal operations. Use of a telnet session is
recommended instead.
f.
Remove the serial cable and protect the port from dust by replacing
the shipping cap.
6.
Connect the active CP card by Ethernet cable to the LAN by completing
the following steps:
a.
Remove the shipping plug from the Ethernet port on the active CP
card.
b.
Insert one end of an Ethernet cable into the Ethernet port.
c.
Connect the other end to an Ethernet 10/100 Base-T LAN.
7. Repeat
Step 6
to connect the standby CP card.
8.
Log in to either of the logical switches by telnet using the administrative
login. The default administrative login name is
admin
and the default
password is
password
.