HP StorageWorks 2/64 HP StorageWorks Core Switch 2/64 Getting Started & Ge - Page 80

To remove power to the HP StorageWorks Core Switch 2/64, IEC 320, EN60320, C20, 16A/250VAC

Get HP StorageWorks 2/64 - Core Switch PDF manuals and user guides View all HP StorageWorks 2/64 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

WARNING To remove power to the HP StorageWorks Core Switch 2/64, disconnect both power cables. The power supplies are universal and capable of functioning worldwide without using voltage jumpers or switches. They meet IEC 61000-4-5 surge voltage requirements and are autoranging in terms of accommodating input voltages and line frequencies. Each power supply has its own built-in fan for cooling, pushing the air towards the port side of the switch. The following power specifications in Table 12 are calculated for fully loaded systems with four power supplies. A fully loaded system has eight 16-port cards, two CP cards, and three blower assemblies. The following table lists the power supply specifications. Table 12. Power Specifications Specification Value Power Receptacle IEC 320, EN60320, C20, 16A/250VAC Total power available from 1 KW each power supply Input voltage 200 - 240 VAC Note System can operate with three-phase or single-phase power utility installation. Input line frequency 50 - 60 Hz Harmonic distortion Active power factor correction per IEC1000-3-2 Heat Output (BTU rating) 64 ports: 1080 Watts, 3690 BTU/hr. 128 ports: 2250 Watts, 6700 BTU/hr. Maximum inrush current 40 Amps Peak per power cord Input line protection Thermal circuit breaker Power supply dimensions 2.74 in.wide, 4.86 in. high, 13.50 in. long 72 getting started and general reference guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
72
getting started and general reference guide
WARNING
To remove power to the HP StorageWorks Core Switch 2/64,
disconnect both power cables.
The power supplies are universal and capable of functioning worldwide
without using voltage jumpers or switches. They meet IEC 61000-4-5 surge
voltage requirements and are autoranging in terms of accommodating input
voltages and line frequencies. Each power supply has its own built-in fan
for cooling, pushing the air towards the port side of the switch.
The following power specifications in
Table 12
are calculated for fully
loaded systems with four power supplies. A fully loaded system has eight
16-port cards, two CP cards, and three blower assemblies.
The following table lists the power supply specifications.
Table 12.
Power Specifications
Specification
Value
Power Receptacle
IEC 320, EN60320, C20, 16A/250VAC
Total power available from
each power supply
1 KW
Input voltage
200 - 240 VAC
Note
System can operate with three-phase or
single-phase power utility installation.
Input line frequency
50 - 60 Hz
Harmonic distortion
Active power factor correction per
IEC1000-3-2
Heat Output (BTU rating)
64 ports: 1080 Watts, 3690 BTU/hr.
128 ports: 2250 Watts, 6700 BTU/hr.
Maximum inrush current
per power cord
40 Amps Peak
Input line protection
Thermal circuit breaker
Power supply dimensions
2.74 in.wide, 4.86 in. high, 13.50 in. long