HP StorageWorks 2/64 HP StorageWorks Core Switch 2/64 Getting Started & Ge - Page 79

Facility Requirements, Power Specifications, Input Power Requirements: 200-240 VAC, 12A, 50-60 Hz.

Get HP StorageWorks 2/64 - Core Switch PDF manuals and user guides View all HP StorageWorks 2/64 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Table 11. Component Weights Component CP Card 16-Port Card Card Filler Panel Cable Management Tray Value 5.6 pounds (2.5 kg) 8.6 pounds (3.9 kg) 3.2 pounds (1.6 kg) 0.6 pounds (0.27 kg) Facility Requirements To ensure correct operation of the switch, the facility where the switch is used must meet the following requirements: • Input Power Requirements: 200-240 VAC, 12A, 50-60 Hz. • Adequate supply circuit, line fusing, and wire size, as specified by the electrical rating on the chassis nameplate. • An air flow of at least 350 cubic feet per minute, available in the immediate vicinity of the switch. • The power specifications listed in Table 12 on page 72. • The environmental specifications listed in Table 13 on page 73. • The electrical interference must be less than the levels stated in the standards listed under "Immunity" in Table 14 on page 74. • When the switch is installed in a rack: - All equipment installed in the rack should have a reliable branch circuit ground connection, and should not rely on a connection to a branch circuit, such as a power strip. - The rack should be balanced and the installed equipment within the rack's weight limits. Ensure the rack is mechanically secured to insure stability in the event of an earthquake. Power Specifications Note System can operate with any of three phases of a three-phase or single-phase power utility installation. Specifications 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Specifications
71
Facility Requirements
To ensure correct operation of the switch, the facility where the switch is
used must meet the following requirements:
•
Input Power Requirements: 200-240 VAC, 12A, 50-60 Hz.
•
Adequate supply circuit, line fusing, and wire size, as specified by the
electrical rating on the chassis nameplate.
•
An air flow of at least 350 cubic feet per minute, available in the
immediate vicinity of the switch.
•
The power specifications listed in
Table 12
on
page 72
.
•
The environmental specifications listed in
Table 13
on
page 73
.
•
The electrical interference must be less than the levels stated in the
standards listed under
“Immunity”
in
Table 14
on
page 74
.
•
When the switch is installed in a rack:
–
All equipment installed in the rack should have a reliable branch
circuit ground connection, and should not rely on a connection to a
branch circuit, such as a power strip.
–
The rack should be balanced and the installed equipment within the
rack’s weight limits. Ensure the rack is mechanically secured to
insure stability in the event of an earthquake.
Power Specifications
Note
System can operate with any of three phases of a three-phase or
single-phase power utility installation.
CP Card
5.6 pounds (2.5 kg)
16-Port Card
8.6 pounds (3.9 kg)
Card Filler Panel
3.2 pounds (1.6 kg)
Cable Management Tray
0.6 pounds (0.27 kg)
Table 11.
Component Weights
Component
Value