HP StorageWorks 2/64 HP StorageWorks Core Switch 2/64 Getting Started & Ge - Page 56

Power Supplies, The HP StorageWorks Core Switch 2/64 only detects modems

Get HP StorageWorks 2/64 - Core Switch PDF manuals and user guides View all HP StorageWorks 2/64 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

• Ethernet port The Ethernet port has an RJ-45 connector and is capable of speeds of 10/100 Mbps. A separate modem can be connected to each modem serial port, and then connected to the same or separate telephone lines for redundancy. Note The HP StorageWorks Core Switch 2/64 only detects modems during power on or reboot. If a modem is connected to an operating switch, the switch must be rebooted in order to detect the modem. The switch can continue to operate while a CP card is replaced. The active CP card controls the following services: • System initialization • Name server • SNMP • Fabric OS • Extended Fabrics • Fabric Watch • Remote Switch • Advanced Web Tools • Zoning To determine the status of a CP card: 1. Check the LED indicators on the CP card. Refer to Table 6 on page 60 for LED interpretation. 2. Check CP card status using the slotShow and haShow commands. For additional information about these commands, refer to the hp StorageWorks fabric os reference. Power Supplies The HP StorageWorks Core Switch 2/64 uses up to four power supplies with a minimum of two required to power a completely loaded chassis. The left power connector provides power to the power supplies in slots #1 and 48 getting started and general reference guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
48
getting started and general reference guide
•
Ethernet port
The Ethernet port has an RJ-45 connector and is capable of speeds of
10/100 Mbps.
A separate modem can be connected to each modem serial port, and then
connected to the same or separate telephone lines for redundancy.
Note
The HP StorageWorks Core Switch 2/64 only detects modems
during power on or reboot. If a modem is connected to an operating switch,
the switch must be rebooted in order to detect the modem.
The switch can continue to operate while a CP card is replaced. The active
CP card controls the following services:
•
System initialization
•
Name server
•
SNMP
•
Fabric OS
•
Extended Fabrics
•
Fabric Watch
•
Remote Switch
•
Advanced Web Tools
•
Zoning
To determine the status of a CP card:
1.
Check the LED indicators on the CP card. Refer to
Table 6
on
page 60
for LED interpretation.
2.
Check CP card status using the
slotShow
and
haShow
commands. For
additional information about these commands, refer to the
hp
StorageWorks fabric os reference
.
Power Supplies
The HP StorageWorks Core Switch 2/64 uses up to four power supplies
with a minimum of two required to power a completely loaded chassis. The
left power connector provides power to the power supplies in slots #1 and