HP StorageWorks MSA1000 HP StorageWorks 2/8q Fibre Channel Switch Management V - Page 104

Load Firmware dialog box messages, Port Loopback Test dialog box messages

Get HP StorageWorks MSA1000 PDF manuals and user guides View all HP StorageWorks MSA1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Switch Manager Load Firmware dialog box messages Table 34: Load Firmware dialog box messages Message Bad checksum/CRC for the firmware image or incorrect firmware image for this type of switch. File was not found. Firmware image had a bad CRC or was invalid for this type of switch. Firmware upload status unknown. Image has been uploaded, but confirmation from the switch was not received. The flash memory on the switch may be too small for this image. Unable to load firmware. Unable to read file. User action Select the correct firmware file for this switch. Verify that the firmware file specified actually exists, or specify a new firmware file. Select a valid firmware image for this type of switch and retry the operation. The application lost communications with the switch while the switch was unpacking the firmware image. If the problem was temporary, examine the firmware versions on the switch to verify that the firmware was unpacked correctly, or upload a new firmware image to the switch. Select an appropriate firmware image for this type of switch and retry the operation. An unspecified error has occurred. Verify that the user has permissions to modify the configuration on the switch, that the switch is reachable in the fabric, and that the fabric is reachable from the user's workstation, and then retry the firmware upload. Verify that the firmware file specified exists and is readable by the user, on a file system readable by the user, or specify a new firmware file. Port Loopback Test dialog box messages Table 35: Port Loopback test dialog box messages Message Attempt to put port in diagnostic state has failed. Unable to continue with port test. External port test requires a loopback device be plugged into the selected port. Click "OK" when loopback device is installed. Failed to correctly restore port states for one or more ports. Invalid frame count value. or Invalid frame size. Must be 36 to 2148. or Invalid hex pattern. Up to 8 hex digits allowed. User action Verify that the user has permissions to modify the configuration on the switch, that the switch is reachable in the fabric, and that the fabric is reachable from the user's workstation, and then retry the configuration change. Verify that a loopback device is attached to the port before starting loopback test. Return to the faceplate view and then select View>Port State to determine which port was not restored to its original state. Select the port, and then select Port>Port Properties to restore the port state. Verify that all information is valid, and then retry the loopback test. 104 HP StorageWorks 2/8q Fibre Channel Switch Management User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
Switch Manager
104
HP StorageWorks 2/8q Fibre Channel Switch Management User Guide
Load Firmware dialog box messages
Port Loopback Test dialog box messages
Table 34:
Load Firmware dialog box messages
Message
User action
Bad checksum/CRC for the firmware image or
incorrect firmware image for this type of
switch.
Select the correct firmware file for this switch.
File was not found.
Verify that the firmware file specified actually
exists, or specify a new firmware file.
Firmware image had a bad CRC or was
invalid for this type of switch.
Select a valid firmware image for this type of
switch and retry the operation.
Firmware upload status unknown. Image has
been uploaded, but confirmation from the
switch was not received.
The application lost communications with the
switch while the switch was unpacking the
firmware image. If the problem was
temporary, examine the firmware versions on
the switch to verify that the firmware was
unpacked correctly, or upload a new firmware
image to the switch.
The flash memory on the switch may be too
small for this image.
Select an appropriate firmware image for this
type of switch and retry the operation.
Unable to load firmware.
An unspecified error has occurred. Verify that
the user has permissions to modify the
configuration on the switch, that the switch is
reachable in the fabric, and that the fabric is
reachable from the user’s workstation, and
then retry the firmware upload.
Unable to read file.
Verify that the firmware file specified exists
and is readable by the user, on a file system
readable by the user, or specify a new
firmware file.
Table 35:
Port Loopback test dialog box messages
Message
User action
Attempt to put port in diagnostic state has
failed. Unable to continue with port test.
Verify that the user has permissions to modify
the configuration on the switch, that the switch
is reachable in the fabric, and that the fabric is
reachable from the user’s workstation, and
then retry the configuration change.
External port test requires a loopback device
be plugged into the selected port. Click “OK”
when loopback device is installed.
Verify that a loopback device is attached to the
port before starting loopback test.
Failed to correctly restore port states for one or
more ports.
Return to the faceplate view and then select
View>Port State
to determine which port was
not restored to its original state. Select the
port, and then select
Port>Port Properties
to
restore the port state.
Invalid frame count value.
or
Invalid frame size. Must be 36 to 2148.
or
Invalid hex pattern. Up to 8 hex digits
allowed.
Verify that all information is valid, and then
retry the loopback test.