Home » HP Manuals » Storage Devices » HP StorageWorks MSA1000 » Manual Viewer

HP StorageWorks MSA1000 HP StorageWorks 2/8q Fibre Channel Switch Management V - Page 139

Enter, to accept the current value shown

View all HP StorageWorks MSA1000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 139 highlights

Command Line Interface Table 51: Set Config port parameters (Continued) Parameter NoClose IOStreamGuard VIEnable PDISCPingEnable Description Loop circuit closure prevention. Enables (True) or disables (False) the loop's ability to remain in the open state indefinitely. True reduces the amount of arbitration on a loop when there is only one device on the loop. The default is False. I/O Stream Guard. Enable (Enable) or disables (Disable) the suppression of RSCN messages. I/O Stream Guard should be enabled only for ports connected to initiator devices. The default is Disable. Enables (True) or disables (False) VI preference routing. The default is False. Enabling VIEnable will disable MFSEnable. Enables (True) or disables (False) the transmission of ping messages from the switch to all devices on a loop port. The default is True. SWITCH Initiates an editing session in which to change switch configuration settings. The system displays each parameter one line at a time and prompts you for a value. For each parameter, enter a new value or press Enter to accept the current value shown in brackets. Table 52 describes the Set Config Switch parameters. Table 52: Set config switch parameters Parameter AdminState BroadcastEnabled DefaultDomainID DomainIDLock SymbolicName R_A_TOV E_D_TOV PrincipalPriority ConfigDescription InteropMode LegacyAddressFormat Description Switch administrative state: online, offline, or diagnostics. The default is Online. Broadcast. Enables (True) or disables (False) forwarding of broadcast frames. The default is True. Default domain ID. The default is 1. Prevents (True) or allows (False) dynamic reassignment of the domain ID. The default is False. Descriptive name for the switch. The name can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is 2/8q FC Switch. Resource Allocation Timeout Value. The number of milliseconds the switch waits to allow two ports to allocate enough resources to establish a link. The default is 10000. Error Detect Timeout Value. The number of milliseconds a port is to wait for errors to clear. The default is 2000. The priority used in the FC-SW-2 principal switch selection algorithm. 1 is high, 255 is low. The default is 254. Switch configuration description. The configuration description can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is 2/8q FC Switch. Propagates just the active zone set throughout the fabric (True, compliant) or the entire zoning database (False, non-compliant). The default is True. (not supported) Available only when the InteropMode parameter is False, this parameter enables (True) or disables (False) the use of legacy address formatting for interoperating with non-FC-SW-2 switches. See Table 52. The default is False. (not supported) HP StorageWorks 2/8q Fibre Channel Switch Management User Guide 139

Section	Page
2/8q FC Switch Management User Guide	1
Contents	3
About This Guide	13
Overview	14
Intended audience	14
Related documentation	14
Conventions	15
Document conventions	15
Text symbols	15
Equipment symbols	16
Getting help	17
HP installation and configuration assistance	17
HP technical support	18
HP storage web site	18
HP authorized reseller	18
1-Switch Manager	19
Getting started	20
Installing Switch Manager	20
Installing Switch Manager on Windows systems	20
Installing Switch Manager on Linux systems	21
Starting Switch Manager	21
Exiting Switch Manager	22
Removing Switch Manager	23
Removing Switch Manager from Windows	23
Removing Switch Manager from Linux	23
Changing the encryption key for the default fabric view file	23
Saving and opening fabric view files	23
Setting Switch Manager preferences	24
Using online help	25
Viewing software version and copyright information	25
Using the Switch Manager user interface	25
Menu bars	26
Tool bar	29
Fabric tree	29
Graphic window	30
Data window and tabs	31
Working status indicator	31
Using the topology display	31
Using the faceplate display	33
Managing fabrics	35
Managing fabric security	35
User account security	35
Fabric services	36
Managing the fabric database	36
Adding a fabric	36
Removing a fabric	37
Opening a fabric view file	37
Saving a fabric view file	38
Rediscovering a fabric	38
Adding a new switch to a fabric	38
Replacing a failed switch	39
Deleting switches and links	39
Displaying fabric information	40
Fabric status	40
Event Browser	41
Active Zoneset data window	44
Zoning a fabric	45
Zoning concepts	45
Using the Zoning Config dialog box	48
Restoring default zoning	48
Merging fabrics and zoning	49
Using the Edit Zoning dialog box	49
Managing zone sets	52
Managing zones	54
Managing aliases	56
Saving the Zoning Database to a File	57
Managing switches	58
Managing user accounts	58
Creating user accounts	59
Removing a user account	59
Changing a user account password	60
Modifying a user account	61
Displaying switch information	62
Name Server data window	63
Switch data window	63
Link data window	64
Port Statistics data window	64
Port Information data window	65
Configured Zonesets data windows	65
Configuring port threshold alarms	66
Exporting name server information to a file	67
Paging a switch	67
Setting the date/time and NTP client	68
Resetting a switch	68
Configuring a switch	68
Configuration wizard	69
Switch properties	69
Network properties	72
Archiving a switch configuration	75
Restoring a switch configuration	75
Restoring the factory default configuration	77
Downloading a support file	78
Installing firmware	78
Displaying hardware status	79
Managing ports	80
Displaying port information	80
Port status	80
Port Statistics data window	82
Port Information data window	84
Name Server data window	85
Configuring ports	85
Port States parameters	86
Port Speed parameters	86
Port Type parameters	87
Interoperability Credits parameters	87
I/O Stream Guard parameters	87
Device Scan parameter	87
Changing the port symbolic name	87
Extending port credits	88
Resetting a port	89
Testing ports	89
Graphing port performance	91
Starting HP StorageWorks Fabric View	91
Exiting HP StorageWorks Fabric View	92
Saving and opening Fabric View files	92
Changing the Default Fabric View File encryption key	93
Setting HP StorageWorks Fabric View preferences	93
Setting the polling frequency	93
Displaying graphs	94
Removing graphs	94
Arranging graphs in the display	94
Customizing graphs	94
Printing graphs	96
Rescaling a selected graph	96
Saving graph statistics to a file	96
Interpreting Switch Manager messages	97
Fabrics File-Open, Save messages	97
Add a Fabric messages	97
Network Properties dialog box messages	98
Switch Properties dialog box messages	99
Port Properties dialog box messages	101
Faceplate display messages	102
Load Firmware dialog box messages	104
Port Loopback Test dialog box messages	104
Extended Credits wizard messages	106
Zoning dialog box messages	106
Restore Configuration dialog box messages	108
Save Fabric View dialog box messages	108
Trap Configuration dialog box messages	109
2-Command Line Interface	111
Logging on to a switch	112
Working with user accounts	112
Working with switch configurations	113
Modifying a configuration	113
Backing up a switch configuration	114
Restoring a switch configuration	115
Commands	116
Admin command	117
Alias command	118
Config command	119
Create Support command	122
Date command	123
Firmware Install command	123
Hardreset command	124
Help command	125
History command	126
Hotreset command	126
Image command	127
Lip command	129
Passwd command	129
Ping command	130
Ps command	130
Quit command	131
Reset command	131
Set command	135
Set Config command	137
Set Log Command	144
Set Port command	146
Set Setup command	147
Show command	150
Show Config command	160
Show Log command	163
Show Perf command	165
Show Setup command	166
Shutdown command	169
Test command	169
Uptime command	171
User command	171
Whoami command	173
Zone Command	174
Zoneset command	176
Zoning command	178

Match case Limit results 1 per page

Command Line Interface

139

HP StorageWorks 2/8q Fibre Channel Switch Management User Guide

SWITCH

Initiates an editing session in which to change switch configuration settings. The

system displays each parameter one line at a time and prompts you for a value. For

each parameter, enter a new value or press

Enter

to accept the current value shown in

brackets.

Table 52

describes the Set Config Switch parameters.

NoClose

Loop circuit closure prevention. Enables (True) or disables

(False) the loop’s ability to remain in the open state

indefinitely. True reduces the amount of arbitration on a loop

when there is only one device on the loop. The default is

False.

IOStreamGuard

I/O Stream Guard. Enable (Enable) or disables (Disable) the

suppression of RSCN messages. I/O Stream Guard should be

enabled only for ports connected to initiator devices. The

default is Disable.

VIEnable

Enables (True) or disables (False) VI preference routing. The

default is False. Enabling VIEnable will disable MFSEnable.

PDISCPingEnable

Enables (True) or disables (False) the transmission of ping

messages from the switch to all devices on a loop port. The

default is True.

Table 52:

Set config switch parameters

Parameter

Description

AdminState

Switch administrative state: online, offline, or diagnostics. The

default is Online.

BroadcastEnabled

Broadcast. Enables (True) or disables (False) forwarding of

broadcast frames. The default is True.

DefaultDomainID

Default domain ID. The default is 1.

DomainIDLock

Prevents (True) or allows (False) dynamic reassignment of the

domain ID. The default is False.

SymbolicName

Descriptive name for the switch. The name can be up to 32

characters excluding #, semicolon (;), and comma (,). The

default is 2/8q FC Switch.

R_A_TOV

Resource Allocation Timeout Value. The number of

milliseconds the switch waits to allow two ports to allocate

enough resources to establish a link. The default is 10000.

E_D_TOV

Error Detect Timeout Value. The number of milliseconds a port

is to wait for errors to clear. The default is 2000.

PrincipalPriority

The priority used in the FC-SW-2 principal switch selection

algorithm. 1 is high, 255 is low. The default is 254.

ConfigDescription

Switch configuration description. The configuration description

can be up to 32 characters excluding #, semicolon (;), and

comma (,). The default is 2/8q FC Switch.

InteropMode

Propagates just the active zone set throughout the fabric (True,

compliant) or the entire zoning database (False,

non-compliant). The default is True. (not supported)

LegacyAddressFormat

Available only when the InteropMode parameter is False, this

parameter enables (True) or disables (False) the use of legacy

address formatting for interoperating with non-FC-SW-2

switches. See

Table 52

. The default is False. (not supported)

Table 51:

Set Config port parameters (Continued)

Parameter

Description