IBM 2109 Service Guide - Page 139
Message, Failing test, Description, Probable cause, Action, Enc_in, CRC_err, TruncFrm, FrmTooLong
 |
UPC - 087944519355
View all IBM 2109 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 139 highlights
| Table 41. Diagnostic error messages (continued) | Message Failing test Description Probable cause Action | DIAG-CMISA1 | Err#2032 | cmiTest An attempt to send a CMI ASIC failure 1 message from ASIC to ASIC failed. | DIAG-CMNOBUF centralMemoryTest The port could not get any buffer. ASIC failure 1 | Err#1029 | DIAG-DATA | Err#266E | Err#306E portLoopbackTest crossPortTest The payload received by the port System board, GBIC 2 did not match the payload module, or fiber cable transmitted. failure | DIAG-ERRSTAT | Err#2640-2647 | Err#3040-3047 | Err#3840-3847 | | | | | | | | | | | | | | | portLoopbackTest crossPortTest spinSilk The port error statistics counter is ASIC, system board, 2 non-zero, meaning an error was GBIC module, or fiber detected when receiving frames. cable failure One of the following status errors occurred: v Enc_in - Encoding error, inside frame v CRC_err - Cyclic redundancy check on frame failed v TruncFrm - Truncated frame v FrmTooLong - Frame too long v BadEOF - Bad end of file v Enc_out - Encoding error, outside frame v BadOrdSet - Bad symbol on fiber-optic cable v DiscC3 - Discarded class 3 frames | DIAG-INIT | Err#264F | Err#304F | Err#384F portLoopbackTest crossPortTest spinSilk The port failed to go active in the ASIC, system board, 2 loopback mode requested. GBIC module, or fiber cable failure | DIAG-INTNIL | Err#2031 cmiTest ASIC failed to get a CMI error ASIC failure 1 (interrupt). | DIAG-INTNOTCLR centralMemoryTest The interrupt bit could not be ASIC failure 1 | Err#102C cleared. | DIAG-LCMEM centralMemoryTest Data read from the central ASIC failure 1 | Err#1027 cmemRetentionTest memory location did not match | data previously written into the | same location. | DIAG-LCMEMTX | Err#1F27 | Err#1028 centralMemoryTest A central memory transmit path System board failure 1 failure: ASIC 1 failed to read ASIC 2 using the transmit path. | DIAG-LCMRS centralMemoryTest A central memory read short: M ASIC failure 1 | Err#1F25 cmemRetentionTest bytes requested but got less than | Err#1025 M bytes. | DIAG-LCMTO centralMemoryTest A central memory timeout: Data ASIC failure 1 | Err#1F26 cmemRetentionTest transfer initiated did not complete | Err#1026 within the timeout period. | DIAG-MEMNULL | Err#0112 ramTest Test failed to malloc. System board failure 1 Appendix C. Error messages 123
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134 -
135 -
136 -
137 -
138 -
139 -
140 -
141 -
142 -
143 -
144 -
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
 |
 |
