IBM 8671 Hardware Maintenance Manual - Page 109

Completing, installation

Get IBM 8671 - Eserver xSeries 235 PDF manuals and user guides
UPC - 087944734307
View all IBM 8671 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

9. Replace the plastic shield covering the bottom portion of the system board. 10. Reinstall the adapter-support bracket in the server (see "Removing and installing the adapter-support bracket" on page 58). Note: You must reinstall the air-baffle assembly when you reinstall the adapter-support bracket. Make sure that no cable is under the adapter-support bracket or interferes with the center fans. Important: To ensure proper cooling and server operation, you must keep the air-baffle cover closed. 11. Reinstall the adapters and plastic dividers that you removed, and reconnect the internal cables that you disconnected. 12. Reinstall the server cover (see "Installing the server bezel and left-side cover (tower model)" on page 100 or "Installing the server bezel and top cover (rack configuration)" on page 103). Note: You must wait approximately 20 seconds after you plug the power cord of your server into an electrical outlet before the power-control button becomes active. 13. Start the Configuration/Setup Utility program and set configuration parameters as needed (see "Starting the Configuration/Setup Utility program" on page 15). Completing the installation To complete your installation, you must reinstall the bezel, reinstall the server cover, reconnect all the cables that you disconnected earlier and, for certain options, run the Configuration/Setup Utility program. Follow the instructions in this section. Attention: v For proper cooling and airflow, replace the server cover before or shortly after turning on the server. Operating the server for extended periods of time (over 30 minutes) with the server cover removed might damage server components. v To ensure proper server operation, do not remove the air-baffle assembly from the server except when installing or removing the components that are under the air-baffle cover. Note: If you have just plugged the power cords of your server into electrical outlets, you will have to wait approximately 20 seconds before pressing the power-control button. Chapter 4. Customer replaceable units 99

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
9.
Replace
the
plastic
shield
covering
the
bottom
portion
of
the
system
board.
10.
Reinstall
the
adapter-support
bracket
in
the
server
(see
“Removing
and
installing
the
adapter-support
bracket”
on
page
58).
Note:
You
must
reinstall
the
air-baffle
assembly
when
you
reinstall
the
adapter-support
bracket.
Make
sure
that
no
cable
is
under
the
adapter-support
bracket
or
interferes
with
the
center
fans.
Important:
To
ensure
proper
cooling
and
server
operation,
you
must
keep
the
air-baffle
cover
closed.
11.
Reinstall
the
adapters
and
plastic
dividers
that
you
removed,
and
reconnect
the
internal
cables
that
you
disconnected.
12.
Reinstall
the
server
cover
(see
“Installing
the
server
bezel
and
left-side
cover
(tower
model)”
on
page
100
or
“Installing
the
server
bezel
and
top
cover
(rack
configuration)”
on
page
103).
Note:
You
must
wait
approximately
20
seconds
after
you
plug
the
power
cord
of
your
server
into
an
electrical
outlet
before
the
power-control
button
becomes
active.
13.
Start
the
Configuration/Setup
Utility
program
and
set
configuration
parameters
as
needed
(see
“Starting
the
Configuration/Setup
Utility
program”
on
page
15).
Completing
the
installation
To
complete
your
installation,
you
must
reinstall
the
bezel,
reinstall
the
server
cover,
reconnect
all
the
cables
that
you
disconnected
earlier
and,
for
certain
options,
run
the
Configuration/Setup
Utility
program.
Follow
the
instructions
in
this
section.
Attention:
v
For
proper
cooling
and
airflow,
replace
the
server
cover
before
or
shortly
after
turning
on
the
server.
Operating
the
server
for
extended
periods
of
time
(over
30
minutes)
with
the
server
cover
removed
might
damage
server
components.
v
To
ensure
proper
server
operation,
do
not
remove
the
air-baffle
assembly
from
the
server
except
when
installing
or
removing
the
components
that
are
under
the
air-baffle
cover.
Note:
If
you
have
just
plugged
the
power
cords
of
your
server
into
electrical
outlets,
you
will
have
to
wait
approximately
20
seconds
before
pressing
the
power-control
button.
Chapter
4.
Customer
replaceable
units
99