Home » IBM Manuals » Desktops » IBM 8671 » Manual Viewer

IBM 8671 Hardware Maintenance Manual - Page 44

messages, Starting, diagnostic, programs

UPC - 087944734307

Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Text messages The diagnostic text message format is as follows: Function Name: Result (test specific string) where: Function Name is the name of the function being tested when the error occurred. This corresponds to the function code (fff) shown in the error code format in the previous section. Result can be one of the following: Passed This result occurs when the diagnostic test is completed without any errors. Failed This result occurs when the diagnostic test discovers an error. User Aborted This result occurs when you stop the diagnostic test before it is complete. Not Applicable This result occurs when you specify a diagnostic test for a device that is not present. Aborted This result occurs when the test could not proceed, for example, because of the system configuration. Warning This result occurs when a possible problem is reported during the diagnostic test, such as when a device driver is not found. test specific string is additional information that you can use to analyze the problem. Starting the diagnostic programs Complete the following steps to start the diagnostic programs: 1. Turn on the server and watch the screen. Note: To run the diagnostic programs, you must start the server with the highest level password that is set. That is, if an administrator password is set, you must enter the administrator password, not the power-on password, to run the diagnostic programs. 2. When the message F2 for Diagnostics appears, press F2. 3. Type the appropriate password; then, press Enter. 4. Select either Extended or Basic from the top of the screen. 5. When the Diagnostic Programs screen appears, select the test you want to run from the list that appears; then, follow the instructions on the screen. Notes: a. You can press F1 while running the diagnostic programs to obtain help information. You also can press F1 from within a help screen to obtain online documentation from which you can select different categories. To exit from the help information and return to where you left off, press Esc. 34 xSeries 235 Type 8671: Hardware Maintenance Manual and Troubleshooting Guide

Section	Page
About this manual	5
Important safety information	5
Online support	5
Contents	7
Chapter 1. General information	11
Related publications	11
Notices and statements used in this book	12
Features and specifications	13
Server controls and indicators	14
Front view	14
Rear view	16
Operator information panel	17
Server power features	18
Turning on the server	18
Turning off the server	19
Standby mode	19
IBM documentation CD	20
System requirements	20
Starting the IBM Documentation Browser	20
Using the IBM Documentation Browser	21
Using the search feature	21
IBM Director	21
Installing IBM Director updates	22
UpdateXpress	23
Chapter 2. Configuration	25
Using the Configuration/Setup Utility program	25
Starting the Configuration/Setup Utility program	25
Choices available from the Configuration/Setup main menu	26
Additional Configuration/Setup Utility menu choices	29
Using passwords	29
Power-on password	29
Administrator password	30
Using the LSI Logic Configuration Utility program	31
Starting the LSI Logic Configuration Utility program	31
Formatting a SCSI hard disk drive	32
Using the ServerGuide Setup and Installation CD	32
ServerGuide features	32
Setup and configuration overview	33
System Partition	34
Typical operating-system installation	34
Setting up or updating multiple servers	35
Installing your operating system without ServerGuide	35
Using ServeRAID Manager	35
Configuring the Gigabit Ethernet controller	36
High-performance Ethernet modes	37
Ethernet port connector	37
Updating the integrated system management firmware	37
Chapter 3. Diagnostics	39
General checkout	39
Diagnostic tools overview	41
POST error logs	41
Viewing error logs from the Configuration/Setup Utility program	42
Viewing error logs from the diagnostic programs	42
ServerGuide error symptoms	42
Small computer system interface messages	43
Diagnostic programs and error messages	43
Text messages	44
Starting the diagnostic programs	44
Viewing the test log	45
Viewing the System Error log	45
Diagnostic error message tables	45
Identifying problems using status LEDs	46
LEDs for Active PCI slots	46
Power-supply LEDs	48
Light path diagnostics	48
Diagnostic panel LEDs	49
Remind button	49
Recovering the BIOS code	50
Power checkout	50
Troubleshooting the Ethernet controller	51
Network connection problems	51
Ethernet controller troubleshooting chart	51
Ethernet controller messages	53
Chapter 4. Customer replaceable units	55
Installation guidelines	55
System reliability considerations	55
Working inside the server with the power on	56
Handling static-sensitive devices	56
Major components of the xSeries 235 Type 8671 server	56
System-board component locations	58
System-board option connectors	58
System-board internal cable connectors	59
System-board external port connectors	60
System-board switches and jumpers	61
System-board LED locations	63
Removing the server door (tower model)	64
Removing the server left-side cover and bezel (tower model)	65
Removing the left-side cover	65
Removing the bezel	66
Removing the server top cover and bezel (rack configuration)	67
Removing the top cover	67
Removing the bezel	68
Removing and installing the adapter-support bracket	68
Working with adapters	70
Adapter considerations	70
Installing a hot-plug adapter (slots 5 and 6)	72
Installing a non-hot-plug adapter (any slot)	74
Cabling example for a ServeRAID controller	76
Working with the 3-Pack Ultra320 Hot-Swap Expansion option	80
Installing the 3-Pack Ultra320 Hot-Swap Expansion option	81
Installing internal drives	84
Internal drive bays	85
Installing a hot-swap hard disk drive	87
Installing a 5.25-inch removable-media drive	88
Memory technology transition	89
Installing memory modules	90
Installing an additional microprocessor	92
Replacing a hot-swap power supply	97
Installing a hot-swap power-supply option	100
Replacing a hot-swap fan	104
Replacing a front fan	106
Replacing a center fan	106
Replacing a rear fan	106
Replacing the battery	107
Completing the installation	109
Installing the server bezel and left-side cover (tower model)	110
Installing the server door (tower model)	112
Installing the server bezel and top cover (rack configuration)	113
Updating your server configuration	114
Connecting external options	114
Installing the external SCSI connector	115
Installing the second serial connector	115
Connecting an external device	116
Cabling the server	116
Keyboard cabling	117
Pointing device cabling	117
Parallel port cabling	117
Serial cabling	117
Advanced System Management Interconnect cabling	117
USB cabling	118
Video cabling	118
Gigabit Ethernet cabling	118
Power cabling	118
Installing the server in a rack	118
Input/output connectors	118
Parallel port	119
Viewing or changing the parallel-port assignments	119
Parallel port connector	120
Video port	120
Keyboard port	120
Auxiliary-device (pointing device) port	120
Ultra320 SCSI system-board connectors	120
SCSI cabling requirements	121
SCSI IDs	121
SCSI connectors	122
Serial ports	122
Viewing or changing the serial-port assignments	122
Serial-port connectors	123
Universal Serial Bus version 1.1 ports	123
USB cables and hubs	123
USB-port connectors	123
Gigabit Ethernet port	123
Ethernet connector	124
RS-485 (ASM interconnect) ports	124
Chapter 5. Service replaceable units	125
Thermal grease	125
System board	126
Microprocessor removal	127
Operator information panel	129
Diskette drive	131
DASD backplane	132
Power-supply (non-hot-swap)	133
Front fan housing	134
Hot-swap card	135
Diagnostics panel card	135
Power reset card	136
Chapter 6. Symptom-to-FRU index	139
Beep symptoms	139
No-beep symptoms	142
Diagnostic panel system error LED	142
Diagnostic error codes	144
Error symptoms	149
Power-supply LED errors	156
POST error codes	157
Service processor error codes	163
SCSI error codes	163
Temperature error messages	163
Fan error messages	164
Power error messages	164
System shutdown	165
Voltage related system shutdown	165
Temperature related system shutdown	166
DASD checkout	166
Host built-in self test (BIST)	166
Bus fault messages	167
Undetermined problems	167
Problem determination tips	168
Chapter 7. Parts listing for the xSeries 235	171
System	172
Keyboard CRUs	174
Power cord CRUs	176
Appendix A. Getting help and technical assistance	177
Before you call	177
Using the documentation	177
Getting help and information from the World Wide Web	177
Software service and support	178
Hardware service and support	178
Appendix B. Related service information	179
Safety information	179
General safety	179
Electrical safety	180
Safety inspection guide	181
Handling electrostatic discharge-sensitive devices	182
Grounding requirements	182
Safety notices (multilingual translations)	182
Appendix C. Notices	215
Edition notice	215
Trademarks	216
Important notes	216
Product recycling and disposal	217
Electronic emission notices	217
Federal Communications Commission (FCC) statement	217
Industry Canada Class A emission compliance statement	218
Australia and New Zealand Class A statement	218
United Kingdom telecommunications safety requirement	218
European Union EMC Directive conformance statement	218
Taiwanese Class A warning statement	219
Chinese Class A warning statement	219

Match case Limit results 1 per page

Text

messages

The

diagnostic

text

message

format

follows:

Function

Name:

Result

(test

specific

string)

where:

Function

Name

the

name

the

function

being

tested

when

the

error

occurred.

This

corresponds

the

function

code

(fff)

shown

the

error

code

format

the

section.

Result

can

one

the

following:

Passed

This

result

occurs

when

the

diagnostic

test

completed

without

any

errors.

Failed

This

result

occurs

when

the

diagnostic

test

discovers

error.

User

Aborted

This

result

occurs

when

you

stop

the

diagnostic

test

before

complete.

Not

Applicable

This

result

occurs

when

you

specify

diagnostic

test

for

device

that

not

present.

Aborted

This

result

occurs

when

the

test

could

not

proceed,

for

example,

because

the

system

configuration.

Warning

This

result

occurs

when

possible

problem

reported

during

the

diagnostic

test,

such

when

device

driver

not

found.

test

specific

string

additional

information

that

you

can

use

analyze

the

problem.

Starting

the

diagnostic

programs

Complete

the

following

steps

start

the

diagnostic

programs:

Turn

the

server

and

watch

the

screen.

Note:

run

the

diagnostic

programs,

you

must

start

the

server

with

the

highest

level

password

that

set.

That

is,

administrator

password

set,

you

must

enter

the

administrator

password,

not

the

power-on

password,

run

the

diagnostic

programs.

When

the

message

for

Diagnostics

appears,

press

F2.

Type

the

appropriate

password;

then,

press

Enter.

Select

either

Extended

Basic

from

the

top

the

screen.

When

the

Diagnostic

Programs

screen

appears,

select

the

test

you

want

run

from

the

list

that

appears;

then,

the

instructions

the

screen.

Notes:

You

can

press

while

running

the

diagnostic

programs

obtain

help

information.

You

also

can

press

from

within

help

screen

obtain

online

documentation

from

which

you

can

select

different

categories.

exit

from

the

help

information

and

return

where

you

left

off,

press

Esc.

xSeries

235

Type

8671:

Hardware

Maintenance

Manual

and

Troubleshooting

Guide