JVC DLA-X550R Instruction Manual - Page 59

Resetting the Lamp Time, Maintaining the Cabinet and Remote Control

Get JVC DLA-X550R PDF manuals and user guides View all JVC DLA-X550R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Resetting the Lamp Time Reset the lamp time when you have replaced the lamp. It provides an estimated timing for lamp replacement Resetting the lamp time from the menu screen 1 Press the [MENU] button to display the menu 2 Select "Function"""Lamp Reset" from the menu Trigger Off Timer ECO Mode Network Remote Code Lamp Reset Function Off Off Off A Resetting the lamp time using the remote control 1 Insert the power plug into the power outlet Make sure that you operate the 2 remote control in the Standby mode (the power plug is inserted into the outlet, but the power is not turned on) 0 Press in the order as shown. 0 Make sure that you press a button within two seconds after the last button is pressed. Press the last button for at least two seconds. Exit Operate Back MENU Select BACK . 3 On the "Reset Lamp Time?" screen, select "Yes" and press the [OK] button 0 The lamp time is reset to zero. Reset Lamp Time? Yes No . Press for 2 seconds or longer . 0 The "LAMP" indicator and "STANDBY/ON" indicator blink alternately for three seconds. After that, the unit switches to the Standby mode. MEMO 0 Reset the lamp time only when you have replaced the lamp. If the lamp time is reset while a lamp is in use, you may lose track of the timing for replacing the lamp. Doing so may result in using the lamp beyond the estimated limit, thereby causing lamp blowout. Maintaining the Cabinet and Remote Control 0 Gently wipe off dirt on the cabinet with a soft cloth. 0 If it is extremely dirty, wet a cloth in water, wring dry and use it to wipe off the dirt, followed by wiping again with a dry cloth. 0 Pay attention to the following as the cabinet may deteriorate in condition or the paint may come off. 0 Do not wipe with thinner or benzine 0 Do not allow prolonged contact with rubber or plastic products 0 Do not spray volatile chemicals such as insecticide Maintenance 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Resetting the Lamp Time
Reset the lamp time when you have replaced the lamp.
It provides an estimated timing for lamp replacement
Resetting the lamp time from the menu
screen
1
Press the [MENU] button to display
the menu
2
Select “Function”
"
“Lamp Reset”
from the menu
.
MENU
BACK
Back
Operate
Select
Exit
A
Off
Lamp Reset
Remote Code
Network
ECO Mode
Off Timer
Trigger
Function
Off
Off
3
On the “Reset Lamp Time?” screen,
select “Yes” and press the [OK] button
0
The lamp time is reset to zero.
.
No
Yes
Reset Lamp Time?
Resetting the lamp time using the remote
control
1
Insert the power plug into the power
outlet
2
Make sure that you operate the
remote control in the Standby mode
(the power plug is inserted into the
outlet, but the power is not turned on)
0
Press in the order as shown.
0
Make sure that you press a button within two
seconds after the last button is pressed.
Press the last button for at least two seconds.
.
Press for 2
seconds or longer
0
The “LAMP” indicator and “STANDBY/ON”
indicator blink alternately for three seconds.
After that, the unit switches to the Standby
mode.
MEMO
0
Reset the lamp time only when you have replaced the
lamp.
If the lamp time is reset while a lamp is in use, you may
lose track of the timing for replacing the lamp. Doing
so may result in using the lamp beyond the estimated
limit, thereby causing lamp blowout.
Maintaining the Cabinet and Remote Control
0
Gently wipe off dirt on the cabinet with a soft cloth.
0
If it is extremely dirty, wet a cloth in water, wring dry and use it to wipe off the dirt, followed by wiping again with a
dry cloth.
0
Pay attention to the following as the cabinet may deteriorate in condition or the paint may come off.
0
Do not wipe with thinner or benzine
0
Do not allow prolonged contact with rubber or plastic products
0
Do not spray volatile chemicals such as insecticide
59
Maintenance