Home » Lantronix Manuals » Electronics Accessories » Lantronix XPort » Manual Viewer

Lantronix XPort XChip - User Guide - Page 11

Additional Documentation, Description, Document - test board

Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

1: Using This Guide Chapter 9: GPIO Interface 10: Firmware Upgrades 11: Monitor Mode 12: Troubleshooting A: Binary to Hexadecimal Conversions B: Compliance Description Provides instructions for configuring the three General Purpose I/O pins (CP1-3). Provides instructions for obtaining the latest firmware and updating the XPort. Provides instructions for accessing and using the command line interface for monitoring the network and diagnosing problems. Describes common problems and error messages and how to contact Lantronix Technical Support. Provides instructions for converting binary numbers to hexadecimals. Provides RoHS compliance information. Additional Documentation Visit the Lantronix Web site at www.lantronix.com/support/documentation for the latest documentation and the following additional documentation. Document XPort Integration Guide XPort Universal Demo Board Quick Start XPort Universal Demo Board User Guide DeviceInstaller Online Help Com Port Redirector User Guide Description Provides information about the XPort hardware, testing the XPort using the demonstration board, and integrating the XPort into your product. Provides the steps for getting the XPort demonstration board up and running. Provides information for using XPort on the demo board. Provides information on using DeviceInstaller to configure IP addresses and locate Lantronix devices on the network. Provides information on using the Lantronix Windowsbased utility to create secure virtual com port. XPort User Guide 11

Section	Page
XPort User Guide	1
Copyright and Trademark	2
Warranty	2
Contacts	2
Disclaimer	3
Revision History	3
Table of Contents	4
List of Tables	9
List of Figures	9
1. Using This Guide	10
Purpose and Audience	10
Chapter Summary	10
Additional Documentation	11
2. Introduction	12
Capabilities	12
Applications	12
Protocol Support	13
Configuration Methods	13
Addresses and Port Numbers	13
IP Address	14
Port Numbers	14
Product Information Label	14
3. Using DeviceInstaller	15
Installing DeviceInstaller	15
Assigning an IP Address	15
Accessing the XPort Using DeviceInstaller	16
Viewing the Current Configuration	16
4. Configuration Using Web Manager	19
Accessing Web Manager Using DeviceInstaller	19
Network Configuration	21
Network Mode	21
Automatic IP Address Configuration	21
Static IP Address Configuration	22
Ethernet Configuration	23
Server Configuration	24
Server Configuration	24
Advanced	25
Host List Configuration	25
Retry Settings	26
Host Information	26
Channel 1 Configuration	26
Serial Settings	26
Connection Settings - UDP	32
Email Configuration	33
Recipients	34
Trigger Configuration	34
Conditions	34
Message Properties	35
Configurable Pin Settings	35
Configurable Pin Functions	36
Apply Settings	36
Apply Defaults	36
5. Configuration via Telnet or Serial Port (Setup Mode)	38
Accessing Setup Mode	38
Exiting Setup Mode	40
6. Setup Mode: Server Configuration	41
Server Configuration (Option 0)	41
IP Address	41
Set Gateway IP Address	42
Netmask: Number of Bits for Host Part	42
Set DNS Server IP Address	42
Change Telnet/Web Manager Password	42
DHCP Name	43
7. Setup Mode: Channel Configuration	44
Channel 1 (Option 1)	44
Baudrate	44
I/F (Interface) Mode	45
RS-232	45
RS-485 2-Wire and RS-422 4-Wire	45
Flow	46
Port Number	46
Connect Mode	47
a) Incoming Connection	48
b) Response	48
c) Active Startup	48
d) Datagram Type	51
e) Modem Mode	51
Send the Escape Sequence (+++) in Modem Mode	53
Show IP addr after 'RING'	54
Auto Increment Source Port	54
Remote IP Address	54
Remote Port	54
DisConnMode	54
Flush Mode (Buffer Flushing)	55
Pack Control	56
Packing Interval	56
Trailing Characters	57
Send Characters	57
DisConnTime (Inactivity Timeout)	57
Send Characters	57
Telnet Terminal Type	57
Channel (Port) Password	58
8. Setup Mode: Advanced Settings	59
Email Settings (Option 3)	59
Mail Server	60
Unit Name	60
Domain Name	60
Recipient 1	60
Recipient 2	60
Trigger 1	60
Trigger 2	61
Trigger 3	61
Expert Settings (Option 5)	61
TCP Keepalive time in seconds	62
ARP Cache Timeout in Seconds	62
CPU Performance	62
Disable Monitor Mode at bootup	63
HTTP Port Number	63
SMTP Port Number	63
RS-485 TX Enable Active Level	63
MTU Size	63
TCP Re-transmission Timeout	63
Enable alternate MAC	64
Ethernet Connection Type	64
Security Settings (Option 6)	64
Disable SNMP	64
SNMP Community Name	65
Disable Telnet Setup	65
Disable TFTP Firmware Upgrade	65
Disable Port 77FE (Hex)	65
Disable Web Server	65
Disable Web Setup	66
Disable ECHO Ports	66
Enable Encryption	66
Enable Enhanced Password	67
Disable Port 77F0 (Hex)	67
Default Settings (Option 7)	67
Channel 1 Configuration Defaults	67
Expert Settings Defaults	68
Security Settings Defaults	68
Email Settings	69
9. GPIO Interface	70
Configurable Pins	70
Features	70
Control Protocol	71
Guidelines	71
Commands	71
Examples	74
10. Firmware Upgrades	75
Obtaining Firmware	75
Reloading Firmware	75
Using TFTP: Graphical User Interface	75
Using TFTP: Command Line Interface	76
Recovering the Firmware Using the Serial Port and DeviceInstaller	77
11. Monitor Mode	78
Entering Monitor Mode Using the Serial Port	78
Entering Monitor Mode Using the Network Port	78
Monitor Mode Commands	78
12. Troubleshooting	81
Problems and Error Messages	81
Technical Support	84
A: Binary to Hexadecimal Conversions	85
Converting Binary to Hexadecimal	85
Conversion Table	85
Scientific Calculator	85
B: Compliance	87