Lantronix XPort XChip - User Guide - Page 54

Show IP addr after 'RING', Auto Increment Source Port, Remote IP Address, Remote Port, DisConnMode - default login

Get Lantronix XPort PDF manuals and user guides View all Lantronix XPort manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

7: Setup Mode: Channel Configuration Disable or enable the XPort's ability to send the escape sequence. The default is Y (Yes) (send the escape sequence). Show IP addr after 'RING' Show IP addr after 'RING' ? Disable or enable the XPort's ability to show the IP address after RING in Modem Mode. The default is Y (Yes), to show the IP address. Auto Increment Source Port Auto increment source port (N) ? _ Y (Yes) auto increment the source port. The XPort increments the port number used with each new connection. Remote IP Address This is the destination IP address used with an outgoing connection. Remote IP Address : ( 0) ( 0) ( 0) ( 0)_ Note: This option does not display when Hostlist is enabled from the ConnectMode prompt (see Connect Mode on page 47 for more information). Remote Port You must set the remote TCP port number for the unit to make outgoing connections. This parameter defines the port number on the target host to which a connection is attempted. Remote Port ( 0) ? _ To connect an ASCII terminal to a host using the unit for login purposes, use the remote port number 23 (Internet standard port number for Telnet services). Note: This option does not display when Hostlist is enabled from the ConnectMode prompt (see Connect Mode on page 47 for more information). DisConnMode This setting determines the conditions under which the unit will cause a network connection to terminate. DisConnMode ( 0) ? _ Notes:  In DisConnMode (Disconnect Mode), Modem Control In drop either drops the connection or is ignored. XPort User Guide 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
7: Setup Mode: Channel Configuration
Disable or enable the XPort’s ability to send the escape sequence. The default is
Y
(Yes) (send the escape sequence).
Show IP addr after 'RING'
Show IP addr after ‘RING’
<Y> ?
Disable or enable the XPort's ability to show the IP address after RING in Modem
Mode. The default is
Y
(Yes), to show the IP address.
Auto Increment Source Port
Auto increment source port (N) ? _
Y
(Yes) auto increment the source port. The XPort increments the port number used
with each new connection.
Remote IP Address
This is the destination IP address used with an outgoing connection.
Remote IP Address : ( 0) ( 0) ( 0) ( 0)_
Note:
This option does not display when Hostlist is enabled from the ConnectMode
prompt (see
Connect Mode
on page 47 for more information).
Remote Port
You must set the remote TCP port number for the unit to make outgoing connections.
This parameter defines the port number on the target host to which a connection is
attempted.
Remote Port ( 0) ? _
To connect an ASCII terminal to a host using the unit for login purposes, use the
remote port number 23 (Internet standard port number for Telnet services).
Note:
This option does not display when Hostlist is enabled from the ConnectMode
prompt (see
Connect Mode
on page 47 for more information).
DisConnMode
This setting determines the conditions under which the unit will cause a network
connection to terminate.
DisConnMode ( 0) ? _
Notes:
In DisConnMode (Disconnect Mode), Modem Control In drop either drops the
connection or is ignored.
XPort User Guide
54