Home » Lantronix Manuals » Electronics Accessories » Lantronix XPort » Manual Viewer

Lantronix XPort XChip - User Guide - Page 68

Expert Settings Defaults, Security Settings Defaults - snmp

Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

8: Setup Mode: Advanced Settings Send '+++' in Modem Mode Show IP addr after 'RING' Auto increment source port Hostlist retry counter Hostlist retry timeout Start character for serial channel 1 All other parameters connection startup) Enabled Enabled Disable 3 250 (msec) 0x0D (CR) 0 Expert Settings Defaults TCP Keepalive time in s 45 ARP Cache timeout in s 600 CPU Performance 0 (Regular) Disable Monitor Mode @ bootup No RS485 tx enable active low HTTP Port Number 80 (1-65535) SMTP Port Number 25 (1-65535) MTU Size (512 - 1400) 0 (resulting in an operational value of 1400) TCP Re-transmission Timeout (500- 500 (ms) 4000) Alternate MAC Disabled ( for OEM use only) Ethernet Connection Type 0 (auto-negotiate) Security Settings Defaults Disable SNMP No SNMP community name public Disable Telnet setup No Disable TFTP Firmware Update No Disable Port 77FEh No Disable Web Server No Disable Web Setup No XPort User Guide 68

Section	Page
XPort User Guide	1
Copyright and Trademark	2
Warranty	2
Contacts	2
Disclaimer	3
Revision History	3
Table of Contents	4
List of Tables	9
List of Figures	9
1. Using This Guide	10
Purpose and Audience	10
Chapter Summary	10
Additional Documentation	11
2. Introduction	12
Capabilities	12
Applications	12
Protocol Support	13
Configuration Methods	13
Addresses and Port Numbers	13
IP Address	14
Port Numbers	14
Product Information Label	14
3. Using DeviceInstaller	15
Installing DeviceInstaller	15
Assigning an IP Address	15
Accessing the XPort Using DeviceInstaller	16
Viewing the Current Configuration	16
4. Configuration Using Web Manager	19
Accessing Web Manager Using DeviceInstaller	19
Network Configuration	21
Network Mode	21
Automatic IP Address Configuration	21
Static IP Address Configuration	22
Ethernet Configuration	23
Server Configuration	24
Server Configuration	24
Advanced	25
Host List Configuration	25
Retry Settings	26
Host Information	26
Channel 1 Configuration	26
Serial Settings	26
Connection Settings - UDP	32
Email Configuration	33
Recipients	34
Trigger Configuration	34
Conditions	34
Message Properties	35
Configurable Pin Settings	35
Configurable Pin Functions	36
Apply Settings	36
Apply Defaults	36
5. Configuration via Telnet or Serial Port (Setup Mode)	38
Accessing Setup Mode	38
Exiting Setup Mode	40
6. Setup Mode: Server Configuration	41
Server Configuration (Option 0)	41
IP Address	41
Set Gateway IP Address	42
Netmask: Number of Bits for Host Part	42
Set DNS Server IP Address	42
Change Telnet/Web Manager Password	42
DHCP Name	43
7. Setup Mode: Channel Configuration	44
Channel 1 (Option 1)	44
Baudrate	44
I/F (Interface) Mode	45
RS-232	45
RS-485 2-Wire and RS-422 4-Wire	45
Flow	46
Port Number	46
Connect Mode	47
a) Incoming Connection	48
b) Response	48
c) Active Startup	48
d) Datagram Type	51
e) Modem Mode	51
Send the Escape Sequence (+++) in Modem Mode	53
Show IP addr after 'RING'	54
Auto Increment Source Port	54
Remote IP Address	54
Remote Port	54
DisConnMode	54
Flush Mode (Buffer Flushing)	55
Pack Control	56
Packing Interval	56
Trailing Characters	57
Send Characters	57
DisConnTime (Inactivity Timeout)	57
Send Characters	57
Telnet Terminal Type	57
Channel (Port) Password	58
8. Setup Mode: Advanced Settings	59
Email Settings (Option 3)	59
Mail Server	60
Unit Name	60
Domain Name	60
Recipient 1	60
Recipient 2	60
Trigger 1	60
Trigger 2	61
Trigger 3	61
Expert Settings (Option 5)	61
TCP Keepalive time in seconds	62
ARP Cache Timeout in Seconds	62
CPU Performance	62
Disable Monitor Mode at bootup	63
HTTP Port Number	63
SMTP Port Number	63
RS-485 TX Enable Active Level	63
MTU Size	63
TCP Re-transmission Timeout	63
Enable alternate MAC	64
Ethernet Connection Type	64
Security Settings (Option 6)	64
Disable SNMP	64
SNMP Community Name	65
Disable Telnet Setup	65
Disable TFTP Firmware Upgrade	65
Disable Port 77FE (Hex)	65
Disable Web Server	65
Disable Web Setup	66
Disable ECHO Ports	66
Enable Encryption	66
Enable Enhanced Password	67
Disable Port 77F0 (Hex)	67
Default Settings (Option 7)	67
Channel 1 Configuration Defaults	67
Expert Settings Defaults	68
Security Settings Defaults	68
Email Settings	69
9. GPIO Interface	70
Configurable Pins	70
Features	70
Control Protocol	71
Guidelines	71
Commands	71
Examples	74
10. Firmware Upgrades	75
Obtaining Firmware	75
Reloading Firmware	75
Using TFTP: Graphical User Interface	75
Using TFTP: Command Line Interface	76
Recovering the Firmware Using the Serial Port and DeviceInstaller	77
11. Monitor Mode	78
Entering Monitor Mode Using the Serial Port	78
Entering Monitor Mode Using the Network Port	78
Monitor Mode Commands	78
12. Troubleshooting	81
Problems and Error Messages	81
Technical Support	84
A: Binary to Hexadecimal Conversions	85
Converting Binary to Hexadecimal	85
Conversion Table	85
Scientific Calculator	85
B: Compliance	87