Lantronix XPort XChip - User Guide - Page 78

Monitor Mode, Entering Monitor Mode Using the Serial Port, Monitor Mode Commands

Get Lantronix XPort PDF manuals and user guides View all Lantronix XPort manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

11. Monitor Mode Monitor Mode is a command-line interface used for diagnostic purposes. There are two ways to enter Monitor Mode: locally using the serial port or remotely using the network. Entering Monitor Mode Using the Serial Port To enter Monitor Mode locally: 1. Follow the same steps used for setting the serial configuration parameters (see Serial Port on page 39). 2. Instead of typing three x keys, however: 3. Type zzz (or xx1) to enter Monitor Mode with network connections. 4. Type yyy (or yy1) to enter Monitor Mode without network connections. A 0> prompt indicates that you have successfully entered Monitor Mode. Entering Monitor Mode Using the Network Port To enter Monitor Mode using a Telnet connection: 1. Establish a Telnet session to the configuration port (9999). The following message appears: MAC address 0080A394616E Software version V6.9.0.2 (130207) XPTEXE AES library version 1.8.2.1 2. Type M (upper case). A 0> prompt indicates that you have successfully entered Monitor Mode. Monitor Mode Commands The following commands are available in Monitor Mode. Many commands have an IP address as an optional parameter (xxx.xxx.xxx.xxx). If you enter the IP address, the command is applied to another unit with that IP address. If you do not enter the IP address, the command is executed locally. Note: All commands must be in capital letters. Responses to some of the commands are in Intel Hex format. XPort User Guide 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
11. Monitor Mode
Monitor Mode is a command-line interface used for diagnostic purposes.
There are two ways to enter Monitor Mode: locally using the serial port or remotely
using the network.
Entering Monitor Mode Using the Serial Port
To enter Monitor Mode locally:
1.
Follow the same steps used for setting the serial configuration parameters
(see
Serial Port
on page 39).
2.
Instead of typing three
x
keys, however:
3. Type
zzz
(or
xx1
) to enter Monitor Mode with network connections.
4. Type
yyy
(or
yy1
) to enter Monitor Mode without network connections.
A
0>
prompt indicates that you have successfully entered Monitor Mode.
Entering Monitor Mode Using the Network Port
To enter Monitor Mode using a Telnet connection:
1.
Establish a Telnet session to the configuration port (9999). The following
message appears:
MAC address 0080A394616E
Software version V6.9.0.2 (130207) XPTEXE
AES library version 1.8.2.1
2. Type
M
(upper case).
A
0>
prompt indicates that you have successfully entered Monitor Mode.
Monitor Mode Commands
The following commands are available in Monitor Mode. Many commands have an IP
address as an optional parameter (xxx.xxx.xxx.xxx). If you enter the IP address, the
command is applied to another unit with that IP address. If you do not enter the IP
address, the command is executed locally.
Note:
All commands must be in capital letters. Responses to some of the commands
are in Intel Hex format.
XPort User Guide
78