Lantronix XPort XChip - User Guide - Page 50

Command String, Result if remote IP is 129.1.2.3 and remote port is, Autostart

Get Lantronix XPort PDF manuals and user guides View all Lantronix XPort manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

7: Setup Mode: Channel Configuration Command String Autostart (Automatic Connection) Hostlist Result if remote IP is 129.1.2.3 and remote port is 1234 If you enable Autostart, the unit automatically connects to the remote IP address and remote port specified when the firmware starts. If you enable this option, the device server scrolls through the hostlist until it connects to a device listed in the hostlist table. Once it connects, the unit stops trying to connect to any others. If this connection fails, the unit continues to scroll through the table until it is able to connect to another IP in the hostlist. Hostlist supports a minimum of 1 and a maximum of 12 entries. Each entry contains the IP address and the port number. The hostlist is disabled for Manual and Modem Modes. The unit does not accept a data connection from a remote device when the hostlist option is enabled. Figure 7-9 Hostlist Option To enable the hostlist: 1. Enter a Connect Mode of 0x20 (2X), where X is any digit. The menu shows you a list of current entries already defined in the product. 2. To delete, modify, or add an entry, select Yes. If you enter an IP address of 0.0.0.0, that entry and all others after it are deleted. XPort User Guide 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
7: Setup Mode: Channel Configuration
Command String
Result if remote IP is 129.1.2.3 and remote port is
1234
Autostart (Automatic
Connection)
If you enable
Autostart
, the unit automatically connects to the
remote IP address and remote port specified when the firmware
starts.
Hostlist
If you enable this option, the device server scrolls through the
hostlist until it connects to a device listed in the hostlist table.
Once it connects, the unit stops trying to connect to any others.
If this connection fails, the unit continues to scroll through the
table until it is able to connect to another IP in the hostlist.
Hostlist supports a minimum of 1 and a maximum of 12 entries.
Each entry contains the IP address and the port number.
The hostlist is disabled for Manual and Modem Modes. The unit
does not accept a data connection from a remote device when
the hostlist option is enabled.
Figure 7-9 Hostlist Option
To enable the hostlist:
1. Enter a
Connect Mode
of 0x20 (2X), where
X
is any digit. The menu shows you
a list of current entries already defined in the product.
2.
To delete, modify, or add an entry, select
Yes
. If you enter an IP address of
0.0.0.0
, that entry and all others after it are deleted.
XPort User Guide
50