Netgear WNR3500Lv2 User Manual - Page 79

Port Triggering Timeout, Disable Port Triggering

Page 79 highlights

RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual 3. Clear the Disable Port Triggering check box. Note: If the Disable Port Triggering check box is selected after you configure port triggering, port triggering is disabled. However, any port triggering configuration information you added to the router is retained even though it is not used. 4. In the Port Triggering Timeout field, enter a value up to 9999 minutes. This value sets the inactivity timer for the designated inbound ports. These ports close when the timer expires. This is required because the router cannot be sure when the application has terminated. 5. Click Add Service. Figure 5-9 6. In the Service Name field, type a descriptive service name. 7. In the Service User field, select Any (the default) to allow this service to be used by any computer on the Internet. Otherwise, select Single address, and enter the IP address of one computer to restrict the service to a particular computer. 8. Select the service type, either TCP or UDP or both (TCP/UDP). If you are not sure, select TCP/UDP. 9. In the Triggering Port field, enter the number of the outbound traffic port that will cause the inbound ports to be opened. 10. Enter the inbound connection port information in the Connection Type, Starting Port, and Ending Port fields. 11. Click Apply. The service appears in the Port Triggering Portmap table. Customizing Your Network Settings v1.0, November 2009 5-20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133

RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Customizing Your Network Settings
5-20
v1.0, November 2009
3.
Clear the
Disable Port Triggering
check box.
4.
In the
Port Triggering Timeout
field, enter a value up to 9999 minutes. This value sets the
inactivity timer for the designated inbound ports. These ports close when the timer expires.
This is required because the router cannot be sure when the application has terminated.
5.
Click
Add Service
.
6.
In the
Service Name
field, type a descriptive service name.
7.
In the
Service User
field, select
Any
(the default) to allow this service to be used by any
computer on the Internet. Otherwise, select
Single address
, and enter the IP address of one
computer to restrict the service to a particular computer.
8.
Select the service type, either
TCP
or
UDP
or both (
TCP/UDP
). If you are not sure, select
TCP/UDP.
9.
In the
Triggering Port
field, enter the number of the outbound traffic port that will cause the
inbound ports to be opened.
10.
Enter the inbound connection port information in the
Connection Type
,
Starting Port
, and
Ending Port
fields.
11.
Click
Apply
. The service appears in the Port Triggering Portmap table.
Note:
If the
Disable Port Triggerin
g check box is selected after you configure port
triggering, port triggering is disabled. However, any port triggering
configuration information you added to the router is retained even though it is
not used.
Figure 5-9