Oki PRO8432WT Pro8432WT - User Guide - Page 100

Replacing the Belt Unit, Life Span of Belt Unit, Procedure for Replacement

Get Oki PRO8432WT PDF manuals and user guides View all Oki PRO8432WT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

4. Maintenance Replacing Consumables and Maintenance Units 14 Close the front cover (2). Note ●● The front cover cannot be closed if the output tray is not closed securely. 4 2 15 Please recycle image drums. Memo ●● If you must dispose of an image drum, put it in a plastic bag or similar container and dispose of it in accordance with your municipality's ordinances or guidelines. ●● If the light-shielding film of the image drum becomes dirty, wipe the film by following the procedures below. (1) Open the front cover. (2) Open the output tray. (3) Remove the image drum. (4) Wipe the light-shielding film with soft tissue paper. Replacing the Belt Unit Life Span of Belt Unit When the "Belt Unit Near Life" message appears on the display screen, prepare a replacement belt unit. You can keep printing approximately 1,000 pages until the next message appears. When the "Change Belt Unit" message appears, replace the belt unit. The life expectancy of the belt unit is approximately 30,000 pages for A4 simplex printing (three pages per job). Note ●● The actual number of pages you can print with the belt unit depends on how you use it. Note ●● Though opening and closing the output tray may extend the life of the belt unit somewhat, you should replace it soon after the "Change Belt Unit" is displayed to prevent malfunction. ●● If you replace the belt unit, use it until the end of its useable life. If you remove the belt unit and install and use another one before its usable life has expired, the use life will not be correctly displayed. ●● Press the scroll button or button > [Admin Setup] > [System Setup] > [Near Life Status] is set to [Disable], the [Belt Unit Near Life] message does not appear. Procedure for Replacement Note ●● The image drum (the green tube) is very delicate. Handle it carefully. ●● Do not expose the image drum to direct sunlight or very bright interior light (approximately more than 1500 lux). Even under the normal interior light, do not leave it for more than 5 minutes. 1 Prepare a replacement belt unit. (5) Put the image drum back to the printer. (6) Close the output tray by pushing the both sides of the cover firmly. (7) Close the front cover. 2 Turn off your printer by pressing the power switch. Reference ●● "Turning Off the Power" P.22 - 100 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
- 100 -
Replacing Consumables and Maintenance Units
4
4. Maintenance
14
Close the front cover (2).
Note
●
The front cover cannot be closed if the output tray is
not closed securely.
2
15
Please recycle image drums.
Memo
●
If you must dispose of an image drum, put it in a
plastic bag or similar container and dispose of it in
accordance with your municipality’s ordinances or
guidelines.
●
If the light-shielding film of the image drum becomes
dirty, wipe the film by following the procedures
below.
(1)
Open the front cover.
(2)
Open the output tray.
(3)
Remove the image drum.
(4)
Wipe the light-shielding film with soft
tissue paper.
(5)
Put the image drum back to the
printer.
(6)
Close the output tray by pushing the
both sides of the cover firmly.
(7)
Close the front cover.
Replacing the Belt Unit
Life Span of Belt Unit
When the “
Belt Unit Near Life
” message
appears on the display screen, prepare a
replacement belt unit. You can keep printing
approximately 1,000 pages until the next
message appears.
When the “
Change Belt Unit
” message
appears, replace the belt unit.
The life expectancy of the belt unit is
approximately 30,000 pages for A4 simplex
printing (three pages per job).
Note
●
The actual number of pages you can print with the belt
unit depends on how you use it.
Note
●
Though opening and closing the output tray may extend
the life of the belt unit somewhat, you should replace it
soon after the “
Change Belt Unit
” is displayed to prevent
malfunction.
●
If you replace the belt unit, use it until the end of its
useable life. If you remove the belt unit and install and
use another one before its usable life has expired, the use
life will not be correctly displayed.
●
Press the scroll button
or
button > [
Admin Setup
] >
[
System Setup
] > [
Near Life Status
] is set to [
Disable
],
the [
Belt Unit Near Life
] message does not appear.
Procedure for Replacement
Note
●
The image drum (the green tube) is very delicate. Handle
it carefully.
●
Do not expose the image drum to direct sunlight or very
bright interior light (approximately more than 1500 lux).
Even under the normal interior light, do not leave it for
more than 5 minutes.
1
Prepare a replacement belt unit.
2
Turn off your printer by pressing the
power switch.
Reference
●
“Turning Off the Power” P.22