Panasonic D10000U Operating Instructions - Page 90

Error information

Get Panasonic D10000U - SXGA+ DLP Projector PDF manuals and user guides
UPC - 791871111413
View all Panasonic D10000U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

How to use network function (continued) ■ Error information page When is displayed on the status information screen, click it to display the error details. • Depending on the nature of the error, the projector may be placed in the standby mode for its own protection. ● When [FAILED] has appeared for an item OK: Normal operation FAILED: Occurrence of trouble Parameter MAIN CPU BUS FAN OPTICS MODULE TEMPERATURE INPUT AIR TEMPERATURE OUTPUT AIR TEMPERATURE LAMP REMAIN TIME LAMP STATUS APERTURE (CONTRAST-SHUTTER) SHUTTER (MUTE-SHUTTER DIRTY AIR FILTER AIR FILTER CLEANER UNIT OPTICS MODULE TEMP. SENSOR INPUT AIR TEMP. SENSOR OUTPUT TEMP. SENSOR BATTERY AIRFLOW SENSOR AC POWER LENS SHIFT Description Trouble has occurred in the microcomputer circuitry. Consult your dealer. Trouble has occurred in the fan or its drive circuit. Consult your dealer. The temperature inside the projector is high. It may be that the projector is being used where the ambient temperature is high such as near a heating appliance. The input air temperature is too high. It may be that the projector is being used where the ambient temperature is high such as near a heating appliance. The temperature around the lamp is too high. It may be that the projector's ventilation holes are blocked. The lamp runtime has exceeded the prescribed cumulative time, and it is now time to replace the lamp. The lamp has failed to light. Wait a short while for the lamp to cool off, and then turn on the power. Trouble has occurred in the contrast shutter circuitry. Consult your dealer. Trouble has occurred in the shutter circuitry. Consult your dealer. The air filter is blocked with dust. Turn off the MAIN POWER switch by following the procedure on page 36, and then clean the air filter. (pp. 108, 109) The air filter unit is not installed. Install the air filter unit. Trouble has occurred in the temperature detection sensor inside the projector. Consult your dealer. Trouble has occurred in the sensor used to detect the input air temperature. Consult your dealer. Trouble has occurred in the sensor used to detect the exhaust air temperature. Consult your dealer. The backup battery has been run out. Consult your dealer. Problem with air flow sensor. Consult your dealer. AC power supply voltage input has dropped. Check that there is sufficient electrical wiring capacity for the projector's power consumption requirements. Problem with lens shift circuit. Consult your dealer. 90 - ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
90
– ENGLISH
Error information page
When
is displayed on the status information screen, click it to display the error
details.
Depending on the nature of the error, the projector may be placed in the standby mode for its own protection.
When [FAILED] has appeared for an item
■
•
●
OK: Normal operation
FAILED: Occurrence of trouble
OK: Normal operation
FAILED: Occurrence of trouble
Parameter
Description
MAIN CPU BUS
Trouble has occurred in the microcomputer circuitry. Consult your dealer.
FAN
Trouble has occurred in the fan or its drive circuit. Consult your dealer.
OPTICS MODULE TEMPERATURE
The temperature inside the projector is high. It may be that the projector is being
used where the ambient temperature is high such as near a heating appliance.
INPUT AIR TEMPERATURE
The input air temperature is too high. It may be that the projector is being used
where the ambient temperature is high such as near a heating appliance.
OUTPUT AIR TEMPERATURE
The temperature around the lamp is too high. It may be that the projector’s
ventilation holes are blocked.
LAMP REMAIN TIME
The lamp runtime has exceeded the prescribed cumulative time, and it is now
time to replace the lamp.
LAMP STATUS
The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
APERTURE
(CONTRAST-SHUTTER)
Trouble has occurred in the contrast shutter circuitry. Consult your dealer.
SHUTTER
(MUTE-SHUTTER
Trouble has occurred in the shutter circuitry. Consult your dealer.
DIRTY AIR FILTER
The air filter is blocked with dust.
Turn off the MAIN POWER switch by following the procedure on page 36, and
then clean the air filter. (pp. 108, 109)
AIR FILTER CLEANER UNIT
The air filter unit is not installed. Install the air filter unit.
OPTICS MODULE TEMP. SENSOR
Trouble has occurred in the temperature detection sensor inside the projector.
Consult your dealer.
INPUT AIR TEMP. SENSOR
Trouble has occurred in the sensor used to detect the input air temperature.
Consult your dealer.
OUTPUT TEMP. SENSOR
Trouble has occurred in the sensor used to detect the exhaust air temperature.
Consult your dealer.
BATTERY
The backup battery has been run out. Consult your dealer.
AIRFLOW SENSOR
Problem with air flow sensor. Consult your dealer.
AC POWER
AC power supply voltage input has dropped. Check that there is sufficient
electrical wiring capacity for the projector’s power consumption requirements.
LENS SHIFT
Problem with lens shift circuit. Consult your dealer.
Parameter
Description
MAIN CPU BUS
Trouble has occurred in the microcomputer circuitry. Consult your dealer.
FAN
Trouble has occurred in the fan or its drive circuit. Consult your dealer.
OPTICS MODULE TEMPERATURE
The temperature inside the projector is high. It may be that the projector is being
used where the ambient temperature is high such as near a heating appliance.
INPUT AIR TEMPERATURE
The input air temperature is too high. It may be that the projector is being used
where the ambient temperature is high such as near a heating appliance.
OUTPUT AIR TEMPERATURE
The temperature around the lamp is too high. It may be that the projector’s
ventilation holes are blocked.
LAMP REMAIN TIME
The lamp runtime has exceeded the prescribed cumulative time, and it is now
time to replace the lamp.
LAMP STATUS
The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
APERTURE
(CONTRAST-SHUTTER)
Trouble has occurred in the contrast shutter circuitry. Consult your dealer.
SHUTTER
(MUTE-SHUTTER
Trouble has occurred in the shutter circuitry. Consult your dealer.
DIRTY AIR FILTER
The air filter is blocked with dust.
Turn off the MAIN POWER switch by following the procedure on page 36, and
then clean the air filter. (pp. 108, 109)
AIR FILTER CLEANER UNIT
The air filter unit is not installed. Install the air filter unit.
OPTICS MODULE TEMP. SENSOR
Trouble has occurred in the temperature detection sensor inside the projector.
Consult your dealer.
INPUT AIR TEMP. SENSOR
Trouble has occurred in the sensor used to detect the input air temperature.
Consult your dealer.
OUTPUT TEMP. SENSOR
Trouble has occurred in the sensor used to detect the exhaust air temperature.
Consult your dealer.
BATTERY
The backup battery has been run out. Consult your dealer.
AIRFLOW SENSOR
Problem with air flow sensor. Consult your dealer.
AC POWER
AC power supply voltage input has dropped. Check that there is sufficient
electrical wiring capacity for the projector’s power consumption requirements.
LENS SHIFT
Problem with lens shift circuit. Consult your dealer.
How to use network function (continued)