TP-Link T1700G-28TQ T1700G-28TQ V1 CLI Reference Guide
TP-Link T1700G-28TQ Manual
 |
View all TP-Link T1700G-28TQ manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T1700G-28TQ manual content summary:
- TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 1
T1700G-28TQ JetStream 24-Port Gigabit Stackable Smart Switch with 4 10GE SFP+ Slots REV1.0.0 1910011380 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 3
14 Chapter 2 User Interface 15 2.1 enable ...15 2.2 service password-encryption 15 2.3 enable password...16 2.4 enable secret ... Stack 21 3.1 switch priority ...21 3.2 switch renumber ...21 3.3 switch stack-port ...22 3.4 switch provision ...23 3.5 show switch ...23 Chapter 4 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 4
4.6 show vlan summary 28 4.7 show vlan brief...28 4.8 show vlan...28 4.9 show interface switchport 29 Chapter 5 MAC-based VLAN Commands 30 5.1 mac-vlan mac-address 30 5.2 mac-vlan ...30 5.3 show mac-vlan...31 5.4 show mac-vlan interface 32 Chapter 6 Protocol VLAN Commands 33 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 5
.7 10.8 10.9 10.10 10.11 10.12 ip http server ...56 ip http max-users ...56 ip http session timeout 57 ip http secure-server 58 ip http secure-protocol 58 ip http secure-ciphersuite 59 ip http secure-max-users 59 ip http secure-session timeout 60 ip http secure-server download certificate 61 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 6
Chapter 12 ARP Inspection Commands 74 12.1 ip arp inspection(global 74 12.2 ip arp inspection trust 74 12.3 ip arp inspection(interface 75 12.4 ip arp inspection limit-rate 75 12.5 ip arp inspection recover 76 12.6 show ip arp inspection 77 12.7 show ip arp inspection interface 77 12.8 show - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 7
download ...91 15.7 remove public-key ...92 15.8 show ip ssh ...93 Chapter 16 IEEE 802.1X Commands 94 16.1 16.2 16.3 16.4 16.5 16.6 16.7 16.8 address 111 show mac address-table vlan 111 Chapter 18 System Configuration Commands 112 18.1 system-time manual 112 18.2 system-time ntp ...112 VI - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 8
ip address-alloc ...119 reset ...120 reboot...120 copy running-config startup-config 121 copy startup-config tftp 121 copy tftp startup-config 122 boot application ...123 remove backup-image 123 firmware ipv6 address autoconfig 132 19.3 ipv6 address link-local 133 19.4 ipv6 address dhcp 133 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 9
19.8 show ipv6 interface 136 Chapter 20 Ethernet Configuration Commands 137 20.1 20.2 20.3 20.4 20.5 20.6 20.7 20.8 20.9 20.10 20.11 20.12 20.13 20.14 20.15 20.16 20.17 20.18 20.19 interface gigabitEthernet 137 interface range gigabitEthernet 137 interface ten-gigabitEthernet 138 interface - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 10
22.3 show monitor session 159 Chapter 23 Port Isolation Commands 160 23.1 port isolation ...160 23.2 show port isolation interface 161 Chapter 24 Loopback Detection Commands 162 24.1 loopback-detection(global 162 24.2 loopback-detection interval 162 24.3 loopback-detection recovery-time 163 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 11
27.14 27.15 27.16 ip igmp snooping(global 192 ip igmp snooping(interface 192 ip igmp snooping rtime 193 ip igmp snooping mtime 193 ip igmp snooping report-suppression 194 ip igmp snooping immediate-leave 194 ip igmp snooping drop-unknown 195 ip igmp snooping last-listener query-inteval 195 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 12
.27 permit ...202 range...202 ip igmp filter ...203 clear ip igmp snooping statistics 204 show ip igmp snooping 204 show ip igmp snooping interface 204 show ip igmp snooping vlan 205 show ip igmp snooping multi-vlan 206 show ip igmp snooping groups 206 show ip igmp snooping querier 207 show - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 13
229 snmp-server host...229 snmp-server engineID 231 snmp-server traps snmp 232 snmp-server traps link-status 233 snmp-server traps 233 snmp-server traps mac 234 snmp-server traps vlan 235 rmon history ...245 30.3 arp timeout...246 30.4 show arp ...246 30.5 show ip arp (interface 247 XII - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 14
.8 31.9 31.10 31.11 31.12 interface vlan ...249 interface loopback 249 switchport...250 shutdown ...250 ip route ...251 description ...251 show interface vlan 252 show ip interface...252 show ip interface brief 253 show ip route ...253 show ip route specify 254 show ip route summary 255 XIII - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 15
device mentioned in this Guide stands for T1700G-28TQ JetStream 24-Port Gigabit Stackable Smart Switch with 4 10GE SFP+ used for configuring LAG (Link Aggregation Group) and LACP (Link Aggregation Control Protocol). Chapter for binding the IP address, MAC address, VLAN and the connected Port number of - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 16
Inspection Commands Provide information about the commands used for protecting the switch from the ARP cheating or ARP Attack. Chapter 13: DoS the System information and System IP, reboot and reset the switch, upgrade the switch system and commands used for cable test. Chapter 19: IPv6 Address - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 17
Chapter 26: MSTP Commands Provide information about the commands used for configuring the MSTP (Multiple Spanning Tree Protocol). Chapter 27: IGMP Snooping Commands Provide information about the commands used for configuring the IGMP Snooping (Internet Group Management Protocol Snooping). Chapter 28 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 18
remotely by a Telnet or SSH connection through an Ethernet port. 1.1.1 Logon by Telnet To log on to the switch by a Telnet connection, please take the following steps: 1. Click Start and type in cmd in the Search programs and files window and press the Enter - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 19
to set up an SSH connection: Password Authentication Mode: It requires username and password, which are both admin by default. Key Authentication Mode: It requires a public key for the switch and a private key for the SSH client software. You can generate the public key and the private key through - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 20
Figure 1-5 Enable SSH function Password Authentication Mode 1. Open the software to log on to the interface of PuTTY. Enter the IP address of the switch into Host Name field; keep the default value 22 in the Port field; select SSH as the Connection type. Figure 1-6 SSH Connection Config 6 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 21
, and then enter enable to enter Privileged EXEC Mode, so you can continue to configure the switch. Figure 1-7 Log on the Switch Key Authentication Mode 1. Select the key type and key length, and generate SSH key. Figure 1-8 Generate SSH Key Note: 1. The key length is in the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 22
key is successfully generated, please save the public key and private key to a TFTP server. Figure 1-9 Save the Generated Key 3. Log on to the switch by Telnet and download the public key file from the TFTP server to the switch, as the following figure shows: Figure 1-10 Download the Public Key 8 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 23
Note: 1. The key type should accord with the type of the key file. 2. The SSH key downloading can not be interrupted. 4. After the public key is downloaded, please log on to the interface of PuTTY and enter the IP address for login. Figure 1-11 SSH Connection Config 9 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 24
enter the login user name. If you log on to the switch without entering password, it indicates that the key has been successfully downloaded. Figure 1-13 Log Mode can also be divided into Interface Ethernet, Interface link-aggregation and some other modes, which is shown as the following diagram. - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 25
User EXEC mode. Global Configuration Mode Use the configure command to enter this mode from Privileged EXEC mode. T1700G-28TQ> T1700G-28TQ# T1700G-28TQ# Use the exit command to disconnect the switch. Use the enable command to access Privileged EXEC mode. Enter the exit command to return to User - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 26
or T1700G-28TQ(config-if-range)# T1700G-28TQ (config-vlan)# Use the end command or press Ctrl+Z to return to Privileged EXEC mode. Enter the exit or the # command to return to Global Configuration mode. A port number must be specified in the interface command. Use the switchport command to switch - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 27
link-aggregation: Configure parameters for a link-aggregation, such as broadcast storm. d). Interface range link you to monitor, configure and manage the switch in Privileged EXEC Mode, Global Configuration Mode EXEC mode by using the enable command. In default case, no password is needed. In Global - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 28
1.4 Conventions 1.4.1 Format Conventions The following conventions are used in this Guide: Items in square brackets [ ] are optional Items in braces { } are required Alternative items are grouped in braces and separated by vertical bars. For example: speed { - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 29
EXEC Mode Example If you have set the password to access Privileged EXEC Mode from User EXEC Mode: T1700G-28TQ>enable Password: T1700G-28TQ# 2.2 service password-encryption Description The service password-encryption command is used to encrypt the password when the password is defined or when the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 30
will follow. By default, the encryption type is switch's service password-encryption, the password in the configuration file will be displayed in the symmetric encrypted form. Example Set the super password as "admin" and unencrypted to access Privileged EXEC Mode from User EXEC Mode: T1700G-28TQ - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 31
access Privileged EXEC Mode from User EXEC Mode. To return to the default configuration, please use no enable secret command. This command uses the fixed length, which you can copy from another switch's configuration file. After the encrypted password is T1700G-28TQ(config)#enable secret 0 admin 17 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 32
Configuration Mode Example Return to Global Configuration Mode from Interface Configuration Mode, and then return to Privileged EXEC Mode: T1700G-28TQ(config-if)# exit T1700G-28TQ(config)#exit T1700G-28TQ# 2.7 end Description The end command is used to return to Privileged EXEC Mode. Syntax end 18 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 33
to Privileged EXEC Mode from Interface Configuration Mode: T1700G-28TQ(config-if)#end T1700G-28TQ# 2.8 show history Description The show history command is used to show the latest 20 commands you entered in the current mode since the switch is powered. Syntax show history Command Mode Privileged - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 34
T1700G-28TQ(config)# clear history 20 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 35
member to the default value as 5, please use no switch priority command. Syntax swtich unitid priority priority no switch unitid priority Parameter priority as 10 in the stack: T1700G-28TQ(config)# switch 1 priority 10 3.2 switch renumber Description The switch renumber command is modify the member - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 36
Modify the unit 1's new member number as 2: T1700G-28TQ(config)# switch 1 renumber 2 3.3 switch stack-port Description The switch stack-port command is used to enable the stack port. To switch the stack port to Ethernet port, please use no switch stack-port command. Port 1/0/25 and 1/0/26 are - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 37
The information of the provisioned member is manually created, or created/updated by the switch member when it joins the stack. switch whose stack member number is 2 and device type is T1700G-28TQRev1: T1700G-28TQ(config)# switch 2 provision T1700G-28TQRev1 3.5 show switch Description The show switch - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 38
-- Display the information of the stack ports. Command Mode Privileged EXEC Mode and any Configuration Mode Example Display the detailed information of the current stack: T1700G-28TQ(config)# show switch detail 24 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 39
VLAN (Virtual Local Area Network) technology is developed for the switch to divide the LAN into multiple logical LANs flexibly. Hosts Mode Example Create VLAN 2-10 and VLAN 100: T1700G-28TQ(config)# vlan 2-10,100 Delete VLAN 2: T1700G-28TQ(config)# no vlan 2 4.2 interface vlan Description The - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 40
contains 16 characters at most. Command Mode VLAN Configuration Mode(VLAN) Example Specify the name of VLAN 2 as "group1": T1700G-28TQ(config)# vlan 2 T1700G-28TQ(config-vlan)# name group1 4.4 switchport general allowed vlan Description The switchport general allowed vlan command is used to add the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 41
the type of port 1/0/4 as tagged: T1700G-28TQ(config)# interface gigabitEthernet 1/0/4 T1700G-28TQ(config-if)# switchport general allowed vlan 2 tagged 4.5 switchport pvid Description The switchport pvid command is used to configure the PVID for the switch ports. Syntax switchport pvid vlan-id - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 42
.1Q VLAN. Syntax show vlan brief Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the brief information of IEEE 802.1Q VLAN: T1700G-28TQ(config)# show vlan brief 4.8 show vlan Description The show vlan command is used to display the information of IEEE 802.1Q VLAN. Syntax - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 43
the detailed information of all VLANs. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of vlan 5: T1700G-28TQ(config)# show vlan id 5 4.9 show interface switchport Description The show interface switchport command is used to display the IEEE 802.1Q - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 44
Global Configuration Mode Example Create VLAN 2 with the MAC address 00:11:11:01:01:12 and the name "TP": T1700G-28TQ(config)#mac-vlan mac-address 00:11:11:01:01:12 vlan 2 description TP 5.2 mac-vlan Description The mac-vlan command is used to enable a port for the MAC-based VLAN feature - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 45
use no mac-vlan command. All the ports are disabled by default. Syntax mac-vlan no mac-vlan Command Mode Interface Configuration Mode Ethernet port 1/0/3 for the MAC-based VLAN feature: T1700G-28TQ(config)#interface gigabitEthernet 1/0/3 T1700G-28TQ(config-if)#mac-vlan 5.3 show mac-vlan Description - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 46
-based VLAN. Syntax show mac-vlan interface Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the enable state of all the ports: T1700G-28TQ(config)#show mac-vlan interface 32 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 47
the template corresponding to the number by the show protocol-vlan template command. Command Mode Global Configuration Mode Example Create a Protocol-based VLAN template named "TP" whose Ethernet protocol type is 0x2024: 33 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 48
T1700G-28TQ(config)#protocol-vlan template name TP frame ether_2 ether-type 2024 6.2 protocol-vlan vlan Example Create Protocol-based VLAN 2 and bind it with Protocol-based VLAN Template 3: T1700G-28TQ(config)# protocol-vlan vlan 2 template 3 6.3 protocol-vlan Description The protocol-vlan - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 49
-vlan template Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of the Protocol-based VLAN templates: T1700G-28TQ(config)# show protocol-vlan template 6.5 show protocol-vlan vlan Description The show protocol-vlan vlan command is used to display the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 50
Example Display information of the Protocol-based VLAN entry: T1700G-28TQ(config)# show protocol-vlan vlan 36 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 51
Configuration Mode Example Enable the Voice VLAN function for VLAN 10: T1700G-28TQ(config)# voice vlan 10 7.2 voice vlan aging Description The voice vlan aging command is used to set the aging time for a voice VLAN. To restore to the default aging time for the Voice VLAN, please use no voice vlan - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 52
pri no voice vlan priority Parameter pri -- Priority, ranging from 0 to 7, and the default value is 6. Command Mode Global Configuration Mode Example Configure the priority of the Voice VLAN as 5: T1700G-28TQ(config)# voice vlan priority 5 7.4 voice vlan mac-address Description The voice vlan mac - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 53
00:11:11:11:11:11 and the mask address FF:FF:FF:00:00:00: T1700G-28TQ(config)#voice vlan mac-address 00:11:11:11:11:11 mask FF:FF:FF:00:00:00 description TP-Phone 7.5 switchport voice vlan mode Description The switchport voice vlan mode command is used to - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 54
ten-gigabitEthernet / interface range ten-gigabitEthernet) Example Enable port 1/0/3 for the Voice VLAN security feature: T1700G-28TQ(config)# interface gigabitEthernet 1/0/3 T1700G-28TQ(config-if)# switchport voice vlan security 7.7 show voice vlan Description The show voice vlan command is used - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 55
show voice vlan oui Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of Voice VLAN OUI: T1700G-28TQ(config)# show voice vlan oui 7.9 show voice vlan switchport Description The show voice vlan switchport command is used to display the Voice - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 56
Example Display the Voice VLAN configuration information of all ports and LAGs: T1700G-28TQ(config)# show voice vlan switchport Display the Voice VLAN configuration information of port 1/0/2: T1700G-28TQ(config)# show voice vlan switchport gigabitEthernet 1/0/2 42 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 57
link aggregation and disaggregation by exchanging LACP packets with its partner. The switch can dynamically group similarly configured ports into a single logical link and enable the static LAG: T1700G-28TQ(config)# interface range gigabitEthernet 1/0/2-4 T1700G-28TQ(config-if-range)# channel-group - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 58
address. When this option is selected, the Aggregate Arithmetic will be based on the source and destination IP addresses of the packets. Command Mode Global Configuration Mode Example Configure the Aggregate Arithmetic for LAG as "src-dst-ip": T1700G-28TQ(config)# port-channel load-balance src-dst - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 59
Parameter pri -- The system priority, ranging from 0 to 65535. It is 32768 by default. Command Mode Global Configuration Mode Example Configure the LACP system priority as 1024 globally: T1700G-28TQ(config)# lacp system-priority 1024 8.4 lacp port-priority Description The lacp port-priority command - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 60
port priority as 2048 for port 4: T1700G-28TQ(config)# interface gigabitEthernet 1/0/4 T1700G-28TQ(config-if)# lacp port-priority 2048 8.5 -group-num -- The EtherChannel Group number, ranging from 1 to 6. By default, it is empty, and will display the information of all EtherChannel Groups. detail - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 61
-group-num -- The EtherChannel Group number, ranging from 1 to 6. By default, it is empty, and will display the information of all LACP groups. Mode Example Display the internal LACP information of EtherChannel Group 1: T1700G-28TQ(config)# show lacp 1 internal 8.8 show lacp sys-id Description - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 62
Syntax show lacp sys-id Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LACP system priority: T1700G-28TQ(config)# show lacp sys-id 48 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 63
Web, Telnet or SSH, so as to protect the settings of the switch from being randomly changed. 9.1 user name (password) Description The user name . It is "admin" by default. 0 -- Specify the encryption type. 0 indicates that an unencrypted password will follow. By default, the encryption type is 0. - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 64
encryption function is enabled in service password-encryption, the password in the configuration file will be displayed in the symmetric encrypted form. Example Add and enable a new admin user named "tplink", of which the password is "admin" and unencrypted: T1700G-28TQ(config)#user name tplink - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 65
form. T1700G-28TQ(config)#user name tplink privilege admin secret 0 admin 9.3 user access-control ip-based Description The user access-control ip-based command is used to limit the IP-range of the users' access. Only the users within the IP-range you set here are allowed to access the switch. To - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 66
control of the user whose IP address is 192.168.0.148: T1700G-28TQ(config)# user access-control ip-based 192.168.0.148 255 by default. Command Mode Global Configuration Mode Example Configure that only the user whose MAC address is 00:00:13:0A:00:01 is allowed to access the switch: T1700G-28TQ(config - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 67
] -- Specify the access interface. These interfaces are enabled by default. Command Mode Global Configuration Mode Example Configure that only the users connected to ports 1/0/2-6 are allowed to access the switch: T1700G-28TQ(config)# user access-control port-based interface range gigabitEthernet - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 68
. Syntax show user account-list Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of the current users: T1700G-28TQ(config)# show user account-list 9.8 show user configuration Description The show user configuration command is used to display the security - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 69
of the Telnet function. Syntax show telnet-status Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display whether the Telnet function is enabled: T1700G-28TQ(config)# show telnet-status 55 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 70
), you can manage the switch through a standard browser. default. The HTTP and HTTPS server function cannot be disabled at the same time. Syntax ip http server no ip http server Command Mode Global Configuration Mode Example Disable the HTTP function: T1700G-28TQ(config)# no ip http server 10.2 ip - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 71
to the HTTP server as 5 and 3: T1700G-28TQ(config)# ip http max-users 5 3 10.3 ip http session timeout Description The ip http session timeout command is used to configure the connection timeout of the HTTP server. To restore to the default timeout time, please use no ip http session timeout command - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 72
: T1700G-28TQ(config)# no ip http secure-server 10.5 ip http secure-protocol Description The ip http secure-protocol command is used to configure the SSL protocol version. To restore to the default SSL version, please use no ip http secure-protocol command. By default, the switch supports SSLv3 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 73
connection as SSL 3.0: T1700G-28TQ(config)# ip http secure-protocol ssl3 10.6 ip http secure-ciphersuite Description The ip http secure-ciphersuite command is used to configure the cipherSuites over the SSL connection supported by the switch. To restore to the default ciphersuite types, please use - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 74
on to the HTTPS server as 5 and 3: T1700G-28TQ(config)# ip http secure-max-users 5 3 10.8 ip http secure-session timeout Description The ip http secure-session timeout command is used to configure the connection timeout of the HTTPS server. To restore to the default timeout time, please use no - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 75
of fe80::1234 T1700G-28TQ(config)# ip http secure-server download certificate ssl-cert ip-address fe80::1234 10.10 ip http secure-server download key Description The ip http secure-server download key command is used to download an SSL key to the switch from TFTP server. Syntax ip http secure-server - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 76
the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234. Command Mode Global Configuration Mode Example Download an SSL key named ssl-key from TFTP server with the IP address of 192.168.0.146: T1700G-28TQ(config)# ip http secure-server download key ssl-key - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 77
Description The show ip http secure-server command is used to display the global configuration of SSL. Syntax show ip http secure-server Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of SSL: T1700G-28TQ(config)# show ip http secure-server - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 78
condition for the ARP Inspection to filter the packets. 11.1 ip source binding Description The ip source binding command is used to bind the IP address, MAC address, VLAN ID and the Port number together manually. You can manually bind the IP address, MAC address, VLAN ID and the Port number together - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 79
Command Mode Global Configuration Mode Example Bind an ACL entry with the IP 192.168.0.1, MAC 00:00:00:00:00:01, VLAN ID 2 and the Port number 1/0/5 manually. And then enable the entry for the ARP detection: T1700G-28TQ(config)#ip source binding host1 192.168.0.1 00:00:00:00:00:01 vlan 2 interface - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 80
5. Command Mode Global Configuration Mode Example Enable the DHCP Snooping function on VLAN 1,4,6-7: T1700G-28TQ(config)#ip dhcp snooping vlan 1,4,6-7 11.4 ip dhcp snooping information option Description The ip dhcp snooping information option command is used to enable the Option 82 function of DHCP - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 81
Mode Example Replace the Option 82 field of the packets with the switch defined one and then send out: T1700G-28TQ(config)#ip dhcp snooping information strategy replace 11.6 ip dhcp snooping information remote-id Description The ip dhcp snooping information remote-id command is used to configure the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 82
: T1700G-28TQ(config)#ip dhcp snooping information remote-id tplink 11.7 ip dhcp snooping information circuit-id Description The ip dhcp default Circuit ID for the Option 82, please use no ip dhcp snooping information circuit-id command. Syntax ip dhcp snooping information circuit-id string no ip - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 83
-gigabitEthernet) Example Configure the Gigabit Ethernet port 1/0/2 to be a Trusted Port: T1700G-28TQ(config)#interface gigabitEthernet 1/0/2 T1700G-28TQ(config-if)#ip dhcp snooping trust 11.9 ip dhcp snooping mac-verify Description The ip dhcp snooping mac-verify command is used to enable the MAC - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 84
1/0/2 T1700G-28TQ(config-if)#ip dhcp snooping mac-verify 11.10 ip dhcp snooping limit rate Description The ip dhcp snooping limit rate command is used to enable the Flow Control feature for the DHCP packets. The excessive DHCP packets will be discarded. To restore to the default configuration - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 85
as 20 packets per second on Gigabit Ethernet port 1/0/2: T1700G-28TQ(config)#interface gigabitEthernet 1/0/2 T1700G-28TQ(config-if)#ip dhcp snooping decline 20 11.12 show ip source binding Description The show ip source binding command is used to display the IP-MAC-VIDPORT binding table. Syntax show - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 86
Privileged EXEC Mode and Any Configuration Mode Example Display the running status of DHCP Snooping: T1700G-28TQ#show ip dhcp snooping 11.14 show ip dhcp snooping interface Description The show ip dhcp snooping interface command is used to display the DHCP Snooping configuration of a desire Ethernet - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 87
Example Display the DHCP Snooping configuration of all Ethernet ports and LAGs: T1700G-28TQ#show ip dhcp snooping interface Display the DHCP Snooping configuration of Gigabit Ethernet port 1/0/5: T1700G-28TQ#show ip dhcp snooping interface gigabitEthernet 1/0/5 73 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 88
arp inspection Command Mode Global Configuration Mode Example Enable the ARP Detection function globally: T1700G-28TQ(config)#ip arp inspection 12.2 ip arp inspection trust Description The ip arp inspection trust command is used to configure the port for which the ARP Detect function is unnecessary - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 89
T1700G-28TQ(config)#interface range gigabitEthernet 1/0/2-6 T1700G-28TQ(config-if-range)#ip arp inspection 12.4 ip arp inspection limit-rate Description The ip arp inspection limit-rate command is used to configure the ARP speed of a specified port. To restore to the default speed, please use no ip - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 90
/second). By default, the value is 15. Command Mode Interface Configuration Mode Example Configure the maximum amount of the received ARP packets per second as 50 pps for Gigabit Ethernet port 1/0/5: T1700G-28TQ(config)#interface gigabitEthernet 1/0/5 T1700G-28TQ(config-if)#ip arp inspection limit - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 91
EXEC Mode and Any Configuration Mode Example Display the ARP detection configuration globally: T1700G-28TQ(config)#show ip arp inspection 12.7 show ip arp inspection interface Description The show ip arp inspection interface command is used to display the interface configuration of ARP detection - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 92
Mode and Any Configuration Mode Example Display the number of the illegal ARP packets received: T1700G-28TQ(config)#show ip arp inspection statistics 12.9 clear ip arp inspection statistics Description The clear ip arp inspection statistics command is used to clear the statistic of the illegal ARP - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 93
the evil programs sending a lot of service requests to the Host. With the DoS Defend enabled, the switch can analyze the specific field of the Enable the DoS defend function globally: T1700G-28TQ(config)#ip dos-prevent 13.2 ip dos-prevent type Description The ip dos-prevent type command is used to - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 94
-flood attack enabled, the switch will limit automatically the forwarding speed of ping packets to 512K when attacked by syn-flood. win-nuke -- winNuke attack. Command Mode Global Configuration Mode Example Enable the DoS Defend Type named Land attack: T1700G-28TQ(config)#ip dos-prevent type land 13 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 95
be got by show logging buffer command. It will be lost when the switch is restarted. Syntax logging buffer no logging buffer Command Mode Global Configuration Mode Example Enable the system log buffer: T1700G-28TQ(config)#logging buffer 14.2 logging buffer level Description The logging buffer level - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 96
T1700G-28TQ(config)#logging buffer level 5 14.3 logging file flash Description The logging file flash command is used to store the log messages in a file in the flash on the switch. To disable the log file flash function, please use no logging file flash command. This function is disabled by default - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 97
the log buffer to the flash, ranging from 1 to 48 hours. By default, the synchronization process takes place every 24 hours. immediate -- The system log Example Specify the log file synchronization frequency as 10 hours: T1700G-28TQ(config)#logging file flash frequency periodic 10 14.5 logging file - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 98
saved to the flash. By default, it is 3 indicating that the log message marked with 0~3 will be saved in the log flash. Command Mode Global Configuration Mode Example Save the log messages with their severities equal or higher than 7 to the flash : T1700G-28TQ(config)#logging file flash level 7 14 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 99
Example Enable log host 2 and set its IP address as 192.168.0.148, the level 5: T1700G-28TQ(config)# logging host index 2 192.168 enabled by default. Syntax logging monitor no logging monitor Command Mode Global Configuration Mode Example Disable logging to the terminal devices: T1700G-28TQ(config)# - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 100
| flash -The output channels: buffer and flash. Clear the information of the two channels, by default. Command Mode Global Configuration Mode Example Clear the information in the log file: T1700G-28TQ(config)# clear logging buffer 14.10 show logging local-config Description The show logging local - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 101
, ranging from 1 to 4. Display the configuration of all the log hosts by default. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of the log host 2: T1700G-28TQ(config)# show logging loghost 2 14.12 show logging buffer Description The show logging - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 102
display. Display all the log information in the log buffer by default. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the log information from level 0 to level 5 in the log buffer: T1700G-28TQ(config)# show logging buffer level 5 14.13 show logging flash Description - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 103
function: T1700G-28TQ(config)# ip ssh server 15.2 ip ssh version Description The ip ssh version command is used to enable the SSH protocol version. To disable the protocol version, please use no ip ssh version command. Syntax ip ssh version { v1 | v2 } no ip ssh version { v1 | v2 } Parameter v1 | v2 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 104
AES128-CBC: T1700G-28TQ(config)# ip ssh algorithm AES128-CBC 15.4 ip ssh timeout Description The ip ssh timeout command is used to specify the idle-timeout time of SSH. To restore to the factory defaults, please use no ip ssh timeout command. Syntax ip ssh timeout value no ip ssh timeout Parameter - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 105
as 30 seconds: T1700G-28TQ(config)# ip ssh timeout 30 15.5 ip ssh max-client Description The ip ssh max-client command is used to specify the maximum number of the connections to the SSH server. To return to the default configuration, please use no ip ssh max-client command. Syntax ip ssh max-client - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 106
server with the IP address fe80::1234: T1700G-28TQ(config)# ip ssh download v1 ssh-key ip-address fe80::1234 15.7 remove public-key Description The remove public-key command is used to remove the SSH public key from the switch. Syntax remove public-key { v1 | v2 } Parameter v1 | v2 -- Select the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 107
15.8 show ip ssh Description The show ip ssh command is used to display the global configuration of SSH. Syntax show ip ssh Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of SSH: T1700G-28TQ(config)# show ip ssh 93 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 108
802.1X function: T1700G-28TQ(config)#dot1x system-auth-control 16.2 dot1x handshake Description The dot1x handshake command is used to enable the handshake feature. The handshake feature is used to detect the connection status between the TP-LINK 802.1x supplicant and the switch. Please disable the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 109
T1700G-28TQ(config)# no dot1x handshake 16.3 dot1x auth-method Description The dot1x auth-method command is used to configure the Authentication Method of IEEE 802.1X and the default 802.1x authentication method is "eap". To restore to the default information between the switch and the client. - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 110
network sources. Command Mode Global Configuration Mode Example Enable the Guest VLAN function for VLAN 5: T1700G-28TQ(config)#dot1x guest-vlan 5 16.5 dot1x quiet-period Description The dot1x quiet-period command is -period time. It ranges from 1 to 999 seconds and the default value is 10 seconds. 96 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 111
time for the switch to wait for the response from supplicant before resending a request to the supplicant, ranging from 1 to 9 in second. By default, it is 3 seconds. Command Mode Global Configuration Mode Example Configure the server's timeout value as 5 seconds: T1700G-28TQ(config)#dot1x timeout - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 112
the repeated authentication request, ranging from 1 to 9 in times. By default, the value is 3. Command Mode Global Configuration Mode Example Configure the maximum transfer times of the repeated authentication request as 5: T1700G-28TQ(config)#dot1x max-reauth-req 5 16.8 dot1x Description The dot1x - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 113
Gigabit Ethernet port 1/0/2: T1700G-28TQ(config)#interface gigabitEthernet 1/0/2 T1700G-28TQ(config-if)#dot1x guest-vlan 16.10 dot1x port-control Description The dot1x port-control command is used to configure the Control Mode of IEEE 802.1X for the specified port. By default, the control mode is - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 114
"authorized-force": T1700G-28TQ(config)#interface gigabitEthernet 1/0/20 T1700G-28TQ(config-if)#dot1x port-control authorized-force 16.11 dot1x port-method Description The dot1x port-method command is used to configure the control type of IEEE 802.1X for the specified port. By default, the control - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 115
(config)#interface gigabitEthernet 1/0/20 T1700G-28TQ(config-if)#dot1x port-method port-based 16.12 radius Description The radius command is used to configure the parameters of radius. Syntax radius { [auth-pri ip] [auth-sec ip] [auth-port port] [acct-pri ip] [acct-sec ip] [acct-port port] [auth-key - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 116
from another switch's configuration file. The password or encrypted-password you configured here will be displayed in the encrypted form. Command Mode Global Configuration Mode Example Configure the IP address of the accounting server as 10.20.1.100 and password as tplink: T1700G-28TQ(config)#radius - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 117
of 802.1X. Syntax show dot1x global Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of 802.1X globally: T1700G-28TQ(config)#show dot1x global 16.15 show dot1x interface Description The show dot1x interface command is used to display all ports or the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 118
show radius accounting Command Mode Privileged EXEC Mode and Any Configuration Modes Example Display the configuration of the accounting server: T1700G-28TQ(config)#show radius accounting 16.17 show radius authentication Description The show radius authentication command is used to display the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 119
be added or removed manually, independent of the aging time. In the stable networks, the static MAC address entries can facilitate the switch to reduce broadcast 6c:23, VLAN1 and port 1 together: T1700G-28TQ(config)# mac address-table static 00:02:58:4f:6c:23 vid 1 interface gigabitEthernet 1/0/1 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 120
. It is 300 by default. Command Mode Global Configuration Mode Example Configure the aging time as 500 seconds: T1700G-28TQ(config)# mac address-table to be forwarded. The filtering address can be added or removed manually, independent of the aging time. Syntax mac address-table filtering mac - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 121
address is 00:1e:4b:04:01:5d: T1700G-28TQ(config)# mac address-table filtering 00:1e:4b default configurations, please use no mac address-table max-mac-count command. Port Security is to protect the switch only be deleted manually. The learned entries will be cleared after the switch is rebooted. - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 122
| filtering ] Parameter dynamic | static | filtering -- The type of your desired entry. By default all the entries are displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of all address entries: T1700G-28TQ(config)# show mac address-table 108 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 123
show mac address-table aging-time Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Aging Time of the MAC address: T1700G-28TQ(config)# show mac address-table aging-time 17.7 show mac address-table max-mac-count Description The show mac address-table max-mac-count - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 124
The ID of the LAG. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the address configuration of port 1/0/1: T1700G-28TQ(config)# show mac address-table interface gigabitEthernet 1/0/1 17.9 show mac address-table count Description The show mac address-table count command - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 125
. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of the MAC address 00:00:00:00:23:00 in VLAN 1: T1700G-28TQ(config)#show mac address-table address 00:00:00:00:23:00 vid 1 17.11 show mac address-table vlan Description The show mac address - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 126
time is 12/20/2010 17:30:35 T1700G-28TQ(config)# system-time manual 12/20/2010-17:30:35 18.2 system-time ntp Description The system-time ntp command is used to configure the time zone and the IP address for the NTP Server. The switch will get UTC automatically if it has connected - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 127
TimeZone for Fiji, Magadan, Auckland, Welington. UTC+13:00 -- TimeZone for Nuku'alofa, Samoa. ntp-server -- The IP address for the Primary NTP Server. backup-ntp-server -- The IP address for the Secondary NTP Server. fetching-rate -- Specify the rate fetching time from NTP server. Command Mode - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 128
server is 139.78.100.163, the fetching-rate is 11 hours: T1700G-28TQ(config)# system-time ntp UTC-12:00 133.100.9.2 139.79.100. are 4 options which are USA, Australia, Europe and New-Zealand respectively. The default value is Europe. Following are the time ranges of each option: USA: Second Sunday - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 129
daylight saving time. The start date is in the current year by default. The time range of the daylight saving time must shorter than one minutes to add during the daylight saving time. It is 60 minutes by default. Command Mode Global Configuration Mode Example Configure the daylight saving time from - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 130
T1700G-28TQ(config)# system-time dst date Apr 1 00:00 2015 Oct 1 00:00 2015 30 18.5 system-time dst recurring Description The system saving time, HH:MM. offset -- The number of minutes to add during the daylight saving time. It is 60 minutes by default. Command Mode Global Configuration Mode 116 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 131
. The length of the name ranges from 1 to 32 characters. By default, it is the device name, for example "T1700G-28TQ". Command Mode Global Configuration Mode Example Configure the system name as TPLINK: T1700G-28TQ(config)# hostname TPLINK 18.7 location Description The location command is used to - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 132
of 32 characters at most. It is "www.tp-link.com" by default. Command Mode Global Configuration Mode Example Configure the system contact information as www.tp-link.com: T1700G-28TQ(config)# contact-info www.tp-link.com 18.9 ip address Description This ip address command is used to configure the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 133
Example Create the VLAN interface 2 with the primary IP address as 192.168.1.1/24 and secondary IP address as 192.168.2.1/24: T1700G-28TQ(config)# interface vlan 2 T1700G-28TQ(config-if)# ip address 192.168.1.1 255.255.255.0 T1700G-28TQ(config-if)# ip address 192.168.2.1 255.255.255.0 secondary 18 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 134
on the VLAN interface 2: T1700G-28TQ(config)# interface vlan 2 T1700G-28TQ(config-if)# no ip address 18.11 reset Description The reset command is used to reset the switch's software. After resetting, all configuration of the switch will restore to the factory defaults and your current settings will - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 135
Mode Privileged EXEC Mode Example Reboot the switch stack: T1700G-28TQ# reboot 18.13 copy running-config startup Syntax copy startup-config tftp ip-address ip-addr filename name Parameter ip-addr -- IP Address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 136
are supported, for example 192.168.0.1 or fe80::1234. name -- Specify the name for the configuration file which would be downloaded. Command Mode Privileged EXEC Mode Example Download the configuration file named as config.cfg to the switch from TFTP server with the IP 192.168.0.148: T1700G-28TQ - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 137
boot application Parameter image1 | image2 -- Specify the image file to be configured. By default, the image1.bin is the startup image and the image2.bin is the backup image image2.bin as the startup image in all switches in the stack: T1700G-28TQ(config)# boot application filename image2 startup 18. - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 138
Mode Privileged EXEC Mode Example Upgrade the switch's backup image file with the file firmware.bin in the TFTP server with the IP address 192.168.0.148, and reboot the switch with this firmware: T1700G-28TQ# firmware upgrade ip-address 192.168.0.148 filename firmware.bin It will only upgrade the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 139
T1700G-28TQ# firmware upgrade ip-address fe80::1234 filename firmware.bin It will only upgrade the backup image. Continue? (Y/N):y Operation OK! Reboot with the backup image? (Y/N): n 18.19 ping Description The ping command is used to test the connectivity between the switch and one node of the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 140
has not been found after 20 maxHops, the connection between the switch and the destination device is failed to establish: T1700G-28TQ# tracert 192.168.0.131 20 Test the connectivity between the switch and the network device with the IP fe80::1234. If the destination device has not been found after - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 141
, Device Name, Device Location, System Contact, Hardware Version, Firmware Version, System Time, Run Time and so on. Syntax show system-info Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the system information: T1700G-28TQ# show system-info 18.22 show image-info - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 142
Configuration Mode Example Display the system current operating configuration: T1700G-28TQ# show running-config 18.25 show startup-config Description The show startup-config command is used to display the current configuration saved in the switch. These configuration settings will not be lost the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 143
Syntax show system-time Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the time information of the switch T1700G-28TQ# show system-time 18.27 show system-time dst Description The show system-time dst command is used to display the DST (Daylight Saving Time) - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 144
Display the NTP mode configuration information of the switch: T1700G-28TQ# show system-time ntp 18.29 show trouble spot of the network. Syntax show cable-diagnostics interface { gigabitEthernet port | ten-gigabitEthernet port } Parameter port -- The number of the port which is selected for Cable test - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 145
Example Display the CPU utilization information of the switch: T1700G-28TQ# show cpu-utilization 18.31 show memory-utilization Description The show memory-utilization and Any Configuration Mode Example Display the memory utilization information of the switch: T1700G-28TQ# show memory-utilization 131 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 146
-28TQ(config)# interface vlan 1 T1700G-28TQ(config-if)# ipv6 enable 19.2 ipv6 address autoconfig Description This command is used to enable the automatic configuration of the ipv6 link-local address. The switch has only one ipv6 link-local address, which can be configured automatically or manually - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 147
of the ipv6 link-local address on VLAN interface 1: T1700G-28TQ(config)# interface vlan 1 T1700G-28TQ(config-if)# ipv6 address autoconfig 19.3 ipv6 address link-local Description The ipv6 address link-local command is used to configure the ipv6 link-local address manually on a specified interface - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 148
dhcp no ipv6 address dhcp Configuration Mode Interface Configuration Mode Example Enable the DHCP Client function on VLAN interface 1: T1700G-28TQ(config)# interface vlan 1 T1700G-28TQ(config-if)# ipv6 address dhcp 19.5 ipv6 address ra Description This command is used to configure the interface - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 149
-64 global address on the interface with the network prefix 3ffe::/64: T1700G-28TQ(config)# interface vlan 1 T1700G-28TQ(config-if)# ipv6 address 3ffe::/64 eui-64 19.7 ipv6 address Description This command is used to manually configure a global IPv6 address on the interface. To remove a global IPv6 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 150
, including ipv6 function status, link-local address and global address, ipv6 multicast groups etc. Syntax show ipv6 interface Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the ipv6 information of the management interface: T1700G-28TQ(config)# show ipv6 interface 136 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 151
number. Command Mode Global Configuration Mode Example To enter the Interface gigabitEthernet Configuration Mode and configure port 2: T1700G-28TQ(config)# interface gigabitEthernet 1/0/2 20.2 interface range gigabitEthernet Description The interface range gigabitEthernet command is used to enter - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 152
Global Configuration Mode Example To enter the Interface gigabitEthernet Configuration Mode and configure Ten-Gigabit Ethernet port 1/0/25: T1700G-28TQ(config)#interface ten-gigabitEthernet 1/0/25 20.4 interface range ten-gigabitEthernet Description The interface range ten-gigabitEthernet command is - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 153
Configuration Mode, and configure Ten Gigabit Ethernet ports 1/0/25 and 1/0/26 at the same time by adding them to one port-list: T1700G-28TQ(config)# interface range ten-gigabitEthernet 1/0/25-26 20.5 description Description The description command is used to add a description to the Ethernet port - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 154
-gigabitEthernet / interface range ten-gigabitEthernet / interface port-channel / interface range port-channel) Example Disable port 1/0/3: T1700G-28TQ(config)# interface gigabitEthernet 1/0/3 T1700G-28TQ(config-if)# shutdown 20.7 flow-control Description The flow-control command is used to enable - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 155
flow-control function for port 1/0/3: T1700G-28TQ(config)# interface gigabitEthernet 1/0/3 T1700G-28TQ(config-if)# flow-control 20.8 duplex Description The duplex command is used to configure the Duplex Mode for an Ethernet port. To return to the default configuration, please use no duplex command - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 156
Example Allow jumbo frame on port 1/0/3: T1700G-28TQ(config)# interface gigabitEthernet 1/0/3 T1700G-28TQ(config-if)# jumbo 20.10 speed Description The speed command is used to configure the Speed Mode for an Ethernet port. To return to the default configuration, please use no speed command. Syntax - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 157
function and specify the detailed parameters in pps mode. Example Set the storm control mode as pps on port 1/0/5: T1700G-28TQ(config)# interface gigabitEthernet 1/0/5 T1700G-28TQ(config-if)# storm-control pps 20.12 storm-control Description The storm-control command is used to enable the broadcast - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 158
that the port is not in pps mode. Example Configure the broadcast storm control rate as 1000 kbps on port 1/0/5: T1700G-28TQ(config)# interface gigabitEthernet 1/0/5 T1700G-28TQ(config-if)# storm-control broadcast kbps 1000 20.13 bandwidth Description The bandwidth command is used to configure the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 159
The ID of the LAG. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Clear the statistic information of all ports and LAGs: T1700G-28TQ(config)# clear counters 20.15 show interface status Description The show interface status command is used to display the connection status of the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 160
Mode and Any Configuration Mode Example Display the connection status of all ports and LAGs: T1700G-28TQ(config)# show interface status Display the connection status of port 1/0/1: T1700G-28TQ(config)# show interface status gigabitEthernet 1/0/1 20.16 show interface counters Description The show - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 161
Any Configuration Mode Example Display the configurations of all Ethernet ports and LAGs: T1700G-28TQ(config)# show interface configuration Display the configurations of port 1/0/2: T1700G-28TQ(config)# show interface configuration gigabitEthernet 1/0/2 20.18 show storm-control Description The show - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 162
Ethernet ports. lag-list -- The list of LAGs. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the bandwidth-limit information of port 1/0/4: T1700G-28TQ(config)# show bandwidth interface gigabitEthernet 1/0/4 148 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 163
The qos command is used to configure CoS (Class of Service) based on port. To return to the default configuration, please use no qos command. Syntax qos cos- Configure the priority of port 1/0/5 as 3: T1700G-28TQ(config)# interface gigabitEthernet 1/0/5 T1700G-28TQ(config-if)# qos 3 21.2 qos dscp - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 164
Priority and CoS value: T1700G-28TQ(config)# qos dscp 21.3 qos queue cos-map Description The qos queue cos-map command is used to configure the mapping relation between IEEE 802.1P priority tag/IEEE 802.1Q tag, CoS value and the TC egress queue. To return to the default configuration, please use - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 165
T1700G-28TQ(config)# qos queue cos-map 5 2 21.4 qos queue dscp-map Description The qos queue dscp-map command is used to configure the mapping relation between DSCP Priority and the CoS value. To return to the default Priority is enabled; the untagged non-IP datagram are mapped based on port priority - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 166
T1700G-28TQ(config)# qos queue dscp-map 10-12 2 21.5 qos queue mode Description The qos queue mode command is used to configure the Schedule Mode. To return to the default to the priority queues and scheduling algorithms you set. On this switch, the priority levels are labeled as TC0, TC1,TC2 ... TC7 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 167
as Weight Round Robin Mode: T1700G-28TQ(config)# qos queue mode wrr 21 queues and scheduling algorithms you set. On this switch, the priority levels are labeled as TC0, TC1 8 queues will take up the bandwidth according to their ratio. The default values of TC0, TC1, TC2, TC3, TC4, TC5,TC6 and TC7 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 168
of TC0, TC1, TC2 and TC3 as 4, 7, 15 and 24: T1700G-28TQ(config)# qos queue mode wrr T1700G-28TQ(config)# qos queue weight 0 4 T1700G-28TQ(config)# qos queue weight 1 7 T1700G-28TQ(config)# qos queue weight 2 15 T1700G-28TQ(config)# qos queue weight 3 24 21.7 show qos interface Description The show - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 169
EXEC Mode and Any Configuration Mode Example Display the configuration of IEEE 802.1P Priority and the mapping relation between cos-id and tc-id: T1700G-28TQ# show qos cos-map 21.9 show qos dscp-map Description The show qos dscp-map command is used to display the configuration of DSCP Priority - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 170
EXEC Mode and Any Configuration Mode Example Display the schedule rule of the egress queues: T1700G-28TQ# show qos queue mode 21.11 show qos status Description The show qos status command Mode Example Display the status of IEEE 802.1P priority and DSCP priority: T1700G-28TQ# show qos status 156 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 171
is used to analyze the monitored packets for monitoring and troubleshooting the network. 22.1 monitor session destination interface Description The session 1 and configure port 1/0/1 as the monitoring port: T1700G-28TQ(config)# monitor session 1 destination interface gigabitEthernet 1/0/1 Delete the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 172
Delete the monitor session 1: T1700G-28TQ(config)# no monitor session 1 22.2 monitor session source interface Description The monitor session source interface command is monitored ports are in the same VLAN or not is not demanded strictly. 4. The monitoring port cannot be link-aggregation member. 158 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 173
(config)# monitor session 1 source interface gigabitEthernet 1/0/4-5,1/0/7 rx Delete port 1/0/4 in monitor session 1 and its configuration: T1700G-28TQ(config)# no monitor session 1 source interface gigabitEthernet 1/0/4 rx 22.3 show monitor session Description The show monitor session command is - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 174
forward list of port 1/0/5: T1700G-28TQ(config)# interface gigabitEthernet 1/0/5 T1700G-28TQ(config-if)# port isolation gi-forward-list 1/0/1-2,1/0/4 po-forward-list 2 Set all Ethernet ports and LAGs to forward list of port 1/0/2, namely restore to the default setting: T1700G-28TQ(config)# interface - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 175
to show its forward port list, ranging from 1 to 6. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the forward-list of port 1/0/2: T1700G-28TQ# show port isolation interface gigabitEthernet 1/0/2 Display the forward-list of all Ethernet ports and LAGs - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 176
Example Enable the loopback detection function globally: T1700G-28TQ(config)# loopback-detection 24.2 loopback-detection interval Description The loopback-detection interval command is used to define the interval of sending loopback detection packets from switch ports to network, aiming at detecting - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 177
integral times of detection interval, ranging from 1 to 100 and the default value is 3. Command Mode Global Configuration Mode Example Configure the recovery-time as 3 times of detection interval: T1700G-28TQ(config)# loopback-detection recovery-time 3 24.4 loopback-detection(interface) Description - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 178
alert | port-based }] [ recovery-mode { auto | manual }] Parameter process-mode -- The mode how the switch processes the detected loops. Alert: When a loop is detected, and recovery-mode as manual for port 2: T1700G-28TQ(config)# interface gigabitEthernet 1/0/2 T1700G-28TQ(config-if)# loopback- - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 179
ten-gigabitEthernet / interface range ten-gigabitEthernet) Example Recover the blocked port 2 to normal status: T1700G-28TQ(config)# interface gigabitEthernet 1/0/2 T1700G-28TQ(config-if)# loopback-detection recover 24.7 show loopback-detection global Description The show loopback-detection global - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 180
port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of loopback detection function and the status of all ports: T1700G-28TQ# show loopback-detection interface Display the configuration of loopback detection function and the status of port - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 181
-- ACL ID, ranging from 500 to 2499. The ID range of Standard-IP ACL ranges is 500-1499 and the Extend-IP ACL is 1500-2499. Command Mode Global Configuration Mode Example Create a standard-IP ACL whose ID is 523: T1700G-28TQ(config)# access-list create 523 25.2 mac access-list Description The mac - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 182
Configuration Mode Example Create a Standard-IP ACL whose ID is 520, and add Rule 10 for it. In the rule, the source IP address is 192.168.0.100, the source IP address mask is 255.255.255.0, and the packets match this rule will be forwarded by the switch: T1700G-28TQ(config)# access-list create 520 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 183
Mode Example Create an Extended-IP ACL whose ID is 2220, and add Rule 10 for it. In the rule, the source IP address is 192.168.0.100, the source IP address mask is 255.255.255.0, and the packets match this rule will be forwarded by the switch: T1700G-28TQ(config)# access-list create 2220 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 184
to discard packets. permit --The operation to forward packets. It is the default value. source-mac -- The source MAC address contained in the rule. source match this rule will be forwarded by the switch: T1700G-28TQ(config)# mac access-list 20 T1700G-28TQ(config-mac-acl)# rule 10 permit smac 00 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 185
name Parameter name -- The Policy Name, ranging from 1 to 16 characters. Command Mode Global Configuration Mode Example Add a Policy named policy1: T1700G-28TQ(config)# access-list policy name policy1 25.7 access-list policy action Description The access-list policy action command is used to add - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 186
/ interface range ten-gigabitEthernet / interface port-channel / interface range port-channel) Example Bind ACL 100 to port 1/0/2: T1700G-28TQ(config)# interface gigabitEthernet 1/0/2 T1700G-28TQ(config-if)# access-list bind acl 100 25.9 access-list bind(interface) Description The access-list bind - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 187
Parameter policy-name -- The name of the policy desired to bind. Command Mode Interface VLAN Mode Example Bind policy1 to VLAN 2: T1700G-28TQ(config)# interface vlan 2 T1700G-28TQ(config-if)# access-list bind policy1 25.11 show access-list Description The show access-list command is used to display - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 188
The Policy Name desired to show. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of a policy named policy1: T1700G-28TQ(config)# show access-list policy policy1 25.13 show access-list bind Description The show access-list bind command is used to display - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 189
Tree Protocol), compatible with both STP and RSTP and subject to IEEE 802.1s, can disbranch a ring network. STP is to block redundant links and backup links as well as optimize paths. 26.1 debug spanning-tree Description The debug spanning-tree command is used to enable debuggning of spanning-tree - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 190
, please use no spanning-tree command. Syntax spanning-tree no spanning-tree Command Mode Global Configuration Mode Example Enable the STP function: T1700G-28TQ(config)# spanning-tree 26.3 spanning-tree(interface) Description The spanning-tree command is used to enable STP function for a port. To - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 191
default configuration, please use no spanning-tree common-config command. CIST (Common and Internal Spanning Tree) is the spanning tree in a switched point -- The P2P link status, with auto, open and close options. By default, the option is auto. If the two ports in the P2P link are root port or - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 192
1/0/1 T1700G-28TQ(config-if)# spanning-tree common-config port-priority 64 ext-cost 100 int-cost 100 portfast enable point-to-point open 26.5 spanning-tree mode Description The spanning-tree mode command is used to configure the STP mode of the switch. To return to the default configurations - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 193
return to the default configuration of the corresponding Instance, please use no spanning-tree mst configuration command. Syntax spanning-tree mst configuration no spanning-tree mst configuration Command Mode Global Configuration Mode Example Enter into the MST configuration mode: T1700G-28TQ(config - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 194
from 1 to 32 characters. Command Mode MST Configuration Mode Example Configure the region name of MST as "region1": T1700G-28TQ(config)# spanning-tree mst configuration T1700G-28TQ(config-mst)# name region1 26.9 revision Description The revision command is used to configure the revision level of MST - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 195
61440. By default, it is 32768. MSTI priority is an important criterion on determining if the switch will be chosen as the root bridge in the specific instance. Command Mode Global Configuration Mode Example Enable the MST Instance 1 and configure its priority as 4096: T1700G-28TQ(config)# spanning - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 196
priority command. Syntax spanning-tree priority pri no spanning-tree priority Parameter pri -- Bridge priority, ranging from 0 to 61440. It is 32768 by default. Command Mode Global Configuration Mode Example Configure the bridge priority as 4096: T1700G-28TQ(config)# spanning-tree priority 4096 182 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 197
the TC-BPDUs received by the switch in a TC Protect Cycle. period -- TC Protect Cycle, ranging from 1 to 10 in seconds. By default, it is 5. Command Mode Global Configuration Mode Example Configure TC Threshold as 30 packets and TC Protect Cycle as 10 seconds: T1700G-28TQ(config)# spanning-tree tc - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 198
, which is the interval to send BPDU packets, and used to test the links. Hello Time ranges from 1 to 10 in seconds and it is 2 by default. Otherwise, 2 * (Hello Time + 1) - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 199
occur in a specific region before the BPDU is discarded, ranging from 1 to 40 in hop. By default, it is 20. Command Mode Global Configuration Mode Example Configure the max-hops of STP as 30: T1700G-28TQ(config)# spanning-tree max-hops 30 26.17 spanning-tree bpdufilter Description The spanning-tree - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 200
1/0/2 T1700G-28TQ(config-if)# spanning-tree bpduguard 26.19 spanning-tree guard loop Description The spanning-tree guard loop command is used to enable the Loop Protect function for a port. Loop Protect is to prevent the loops in the network brought by recalculating STP because of link failures - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 201
gigabitEthernet / interface ten-gigabitEthernet / interface range ten-gigabitEthernet) Example Enable the Root Protect function for port 2: T1700G-28TQ(config)# interface gigabitEthernet 1/0/2 T1700G-28TQ(config-if)# spanning-tree guard root 26.21 spanning-tree guard tc Description The spanning-tree - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 202
-BPDUs. If a malicious user continuously sends TC-BPDUs to a switch, the switch will be busy with removing MAC address entries, which may decrease the the TC Protect of Spanning Tree for port 2: T1700G-28TQ(config)# interface gigabitEthernet 1/0/2 T1700G-28TQ(config-if)# spanning-tree guard tc 26.22 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 203
. Syntax show spanning-tree active Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the active information of spanning-tree: T1700G-28TQ(config)# show spanning-tree active 26.24 show spanning-tree bridge Description The show spanning-tree bridge command is used to display - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 204
Any Configuration Mode Example Display the spanning-tree information of all ports: T1700G-28TQ(config)# show spanning-tree interface Display the spanning-tree information of port 1/0/2: T1700G-28TQ(config)# show spanning-tree interface gigabitEthernet 1/0/2 Display the spanning-tree mode information - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 205
Mode Example Display the region information and mapping information of VLAN and MST Instance: T1700G-28TQ(config)#show spanning-tree mst configuration Display the related information of MST Instance 1: T1700G-28TQ(config)#show spanning-tree mst instance 1 Display all the ports information of MST - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 206
2 switch. It can effectively prevent multicast groups being broadcasted in the network. 27.1 ip igmp snooping(global) Description The ip igmp Example Enable IGMP Snooping function: T1700G-28TQ(config)# ip igmp snooping 27.2 ip igmp snooping(interface) Description The ip igmp snooping command is used - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 207
Specify IGMP Snooping router port aging time as 100 seconds globally: T1700G-28TQ(config)# ip igmp snooping rtime 100 27.4 ip igmp snooping mtime Description The ip igmp snooping mtime command is used to specify member port aging time globally. The default aging time is 260 seconds. To restore the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 208
is disabled by default. Syntax ip igmp snooping report-suppression no ip igmp snooping report-suppression Command Mode Global Configuration Mode Example Enable the IGMP report suppression function: T1700G-28TQ(config)# ip igmp snooping report-suppression 27.6 ip igmp snooping immediate-leave - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 209
unknown multicast as discard: T1700G-28TQ(config)# ip igmp snooping drop-unknown 27.8 ip igmp snooping last-listener query-inteval Description The ip igmp snooping last-listener query-inteval command is used to specify the interval to send Specific Query Message. The default value is 1 second. To - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 210
Message to 3 seconds: T1700G-28TQ(config)# ip igmp snooping last-listener query-inteval 3 27.9 ip igmp snooping last-listener query-count Description The ip igmp snooping last-listener query-count command is used to specify the numbers of Specific Query Message to be sent. The default value is 2. To - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 211
seconds. By default, it is 0 and the global router-time will be used. member-time -- Member Port Time. Within this time, if the switch does not T1700G-28TQ(config)# ip igmp snooping vlan-config 1-3 rtime 300 T1700G-28TQ(config)# ip igmp snooping vlan-config 1-3 mtime 200 T1700G-28TQ(config)# ip - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 212
. If not specified, the default multicast VLAN will be selected. router-time -- Router Port Time. Within this time, if the switch does not receive IGMP query Router Port port 1/0/3: T1700G-28TQ(config)# ip igmp snooping multi-vlan-config 3 rtime 100 T1700G-28TQ(config)# ip igmp snooping multi-vlan - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 213
of VLAN 1: T1700G-28TQ(config)#ip igmp snooping querier vlan 1 27.13 ip igmp snooping querier vlan (general query) Description The ip igmp snooping querier vlan command is used to configure the parameters for IGMP Snooping Querier to send a general query frame. To return to the default configuration - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 214
multicast IP or a broadcast IP. By default, it is 192.168.0.1. Command Mode Global Configuration Mode Example For VLAN 2, specify its query-interval as 200 seconds, and the response-time as 20 seconds: T1700G-28TQ(config)#ip igmp snooping querier vlan 2 query-interval 200 T1700G-28TQ(config)#ip igmp - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 215
the throttling action as replace: T1700G-28TQ(config)#interface range gigabitEthernet 1/0/2-5 T1700G-28TQ(config-if-range)#ip igmp snooping max-groups 10 T1700G-28TQ(config-if-range)#ip igmp snooping max-groups action replace 27.15 ip igmp profile Description The ip igmp profile command is used to - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 216
profile as deny. Syntax deny Command Mode Profile Configuration Mode Example Configure the filtering mode of profile 1 as deny: T1700G-28TQ(config)# ip igmp profile 1 T1700G-28TQ(config-igmp-profile)#deny 27.17 permit Description The permit command is used to configure the filtering mode of profile - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 217
of the filter multicast address entry as range 225.1.1.1 to 226.3.2.1 in profile 1: T1700G-28TQ(config)# ip igmp profile 1 T1700G-28TQ(config-igmp-profile)#range 225.1.1.1 226.3.2.1 27.19 ip igmp filter Description The ip igmp filter command is used to bind the specified profile to the interface. To - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 218
Privileged EXEC Mode and Any Configuration Mode Example Clear the statistics of the IGMP packets: T1700G-28TQ(config)# clear ip igmp snooping statistics 27.21 show ip igmp snooping Description The show ip igmp snooping command is used to display the global configuration of IGMP snooping. Syntax show - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 219
Display the IGMP baisic configuration configuration of all ports and LAGs: T1700G-28TQ# show ip igmp snooping interface basic-config Display the IGMP basic configuration of port 1/0/2: T1700G-28TQ# show ip igmp snooping interface gigabitEthernet 1/0/2 basic-config Display the IGMP packet statistics - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 220
Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Multicast VLAN configuration: T1700G-28TQ# show ip igmp snooping multi-vlan 27.25 show ip igmp snooping groups Description The show ip igmp snooping groups command is used to display the information of all IGMP snooping groups - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 221
igmp snooping groups vlan 5 count Display the dynamic multicast groups of VLAN 5 T1700G-28TQ(config)#show ip igmp snooping groups vlan 5 dynamic Display the static multicast groups of VLAN 5 T1700G-28TQ(config)#show ip igmp snooping groups vlan 5 static Display the count of dynamic multicast entries - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 222
or a specific profile. Syntax show ip igmp profile [ id ] Parameter id -- Specify the ID of the profile, ranging from 1 to 999. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of all profiles: T1700G-28TQ(config)# show ip igmp profile 208 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 223
Snooping) is a multicast control mechanism running on Layer 2 switch. It can effectively prevent multicast groups being broadcasted in the snooping Command Mode Global Configuration Mode Example Enable MLD Snooping: T1700G-28TQ(config)# ipv6 mld snooping 28.2 ipv6 mld snooping(interface) Description - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 224
the aging time in seconds, ranging from 60 to 600. The default aging time is 300 seconds. Command Mode Global Configuration Mode Example Specify MLD Snooping router port aging time as 100 seconds globally: T1700G-28TQ(config)# ipv6 mld snooping rtime 100 28.4 ipv6 mld snooping mtime Description - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 225
suppression function. When it is enabled, the switch forwards only the first MLD report message per default. Syntax ipv6 mld snooping report-suppression no ipv6 mld snooping report-suppression Command Mode Global Configuration Mode Example Enable MLD Report message suppression function: T1700G-28TQ - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 226
use no ipv6 mld snooping drop-unknown command. By default, it is disabled. Syntax ipv6 mld snooping drop-unknown no ipv6 mld snooping drop-unknown Command Mode Global Configuration Mode Example Enable unknown multicast filter function: T1700G-28TQ(config)# ipv6 mld snooping drop-unknown 28.8 ipv6 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 227
Message to be sent. The default value is 2. To restore the default number, please use no ipv6 number of Specific Query Message to 3: T1700G-28TQ(config)# ipv6 mld snooping last-listener query mld snooping vlan-config vlan-id-list static ip interface { gigabitEthernet port-list | ten-gigabitEthernet - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 228
config)# ipv6 mld snooping vlan-config 1-3 rtime 300 T1700G-28TQ(config)# ipv6 mld snooping vlan-config 1-3 mtime 200 T1700G-28TQ(config)# ipv6 mld snooping vlan-config 1-2 rport interface gigabitEthernet 1/0/1 Add static multicast IP address ff01::1234:01, which corresponds to VLAN 2, and configure - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 229
If not specified, the default multicast VLAN will be selected. router-time -- Router Port Time. Within this time, if the switch does not receive MLD T1700G-28TQ(config)# ipv6 mld snooping multi-vlan-config 3 rtime 100 T1700G-28TQ(config)# ipv6 mld snooping multi-vlan-config 3 mtime 100 T1700G-28TQ - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 230
MLD Querier function on VLAN 2: T1700G-28TQ(config)# ipv6 mld snooping querier vlan default configuration, please use no ipv6 mld snooping querier vlan command. Syntax ipv6 mld snooping querier vlan vlan-id { query-interval interval | max-response-time response-time | general-query source-ip ip - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 231
Querier. It should not be a multicast IP or a broadcast IP. By default, it is fe80::02ff:ffff:fe00:0001. Command Mode Global Configuration Mode Example For VLAN 2, specify its query-interval as 200 seconds, and the response-time as 20 seconds: T1700G-28TQ(config)#ipv6 mld snooping querier vlan - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 232
groups that ports 1/0/2-5 can join as 10, and configure the throttling action as replace: T1700G-28TQ(config)#interface range gigabitEthernet 1/0/2-5 T1700G-28TQ(config-if-range)#ipv6 mld snooping max-groups 10 T1700G-28TQ(config-if-range)#ipv6 mld snooping max-groups action replace 28.15 ipv6 mld - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 233
mld profile 1 T1700G-28TQ(config-mld-profile)#permit 28.18 range Description The range command is used to configure the range of the profile's filtering multicast address. To delete the corresponding filtering multicast address, please use no range command. A profile contains 16 filtering IP-range - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 234
filter entry.. end-ip -- End IPv6 multicast address of the filter entry. Command Mode Profile Configuration Mode Example Configure one of the filter multicast address entry as range ff80::1234 to ff80::1235 in profile 1: T1700G-28TQ(config)# ipv6 mld profile 1 T1700G-28TQ(config-mld-profile)#range - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 235
. Syntax show ipv6 mld snooping Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of MLD Snooping: T1700G-28TQ(config)# show ipv6 mld snooping 28.22 show ipv6 mld snooping interface Description The show ipv6 mld snooping interface command is used - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 236
Mode Example Display the MLD baisic configuration configuration of all ports and LAGs: T1700G-28TQ# show ipv6 mld snooping interface basic-config Display the MLD basic configuration of port 1/0/2: T1700G-28TQ# show ipv6 mld snooping interface gigabitEthernet 1/0/2 basic-config Display the MLD packet - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 237
. Syntax show ipv6 mld snooping multi-vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Multicast VLAN configuration: T1700G-28TQ# show ipv6 mld snooping multi-vlan 28.25 show ipv6 mld snooping groups Description The show ipv6 mld snooping groups command is used - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 238
VLAN ID selected to display, ranging from 1 to 4094. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display all Querier information: T1700G-28TQ(config)# show ipv6 mld snooping querier 28.27 show ipv6 mld profile Description The show ipv6 mld profile command is used to display - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 239
used to enable the SNMP function. By default, it is disabled. To return to the default configuration, please use no snmp-server command. Syntax snmp-server no snmp-server Command Mode Global Configuration Mode Example Enable the SNMP function: T1700G-28TQ(config)# snmp-server 29.2 snmp-server view - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 240
20, and this OID can be managed by the SNMP management station: T1700G-28TQ(config)# snmp-server view view1 1.3.6.1.6.3.20 include 29.3 snmp-server group Security Model, with v1、v2c and v3 options. They represent SNMP v1, SNMP v2c and SNMP v3. slev -- The Security Level of SNMP v3 Group. There are - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 241
group 1: T1700G-28TQ(config)# no snmp-server group group1 smode v3 slev authNoPriv 29.4 snmp-server user Description The snmp-server user command is used to add User. To delete the corresponding User, please use no snmp-server user command. The User in an SNMP Group can manage the switch via the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 242
the corresponding Group according to its Group Name, Security Model and Security Level. smode -- The Security Model of the User, with v1, v2c and v3 options. By default, the option is v1. The Security Model of the User must be the same with that of the Group which the User belongs to. slev -- The - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 243
T1700G-28TQ(config)# snmp-server user admin local group2 smode v3 slev authPriv cmode MD5 cpwd 11111 emode DES epwd 22222 29.5 snmp-server community Description The snmp-server community command is used to add Community. - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 244
user-name [ smode { v1 | v2c | v3 }] [ slev { noAuthNoPriv | authNoPriv | authPriv }] [ type { trap | inform }] [ retries retries ] [ timeout timeout ] no snmp-server host ip user-name Parameter ip -- The IP Address of the management Host. Both IPv4 and IPv6 addresses are supported, for example 192 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 245
time as 100: T1700G-28TQ(config)# snmp-server host fe80::1234 162 admin smode v2c type inform retries 100 timeout 1000 29.7 snmp-server engineID Description The snmp-server engineID command is used to configure the local and remote engineID of the switch. To restore to the default setting, please - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 246
enabled. auth-failure -- Enable the auth-failure trap. It is sent when a received SNMP request fails the authentication. By default, it is enabled. Command Mode Global Configuration Mode Example Enable SNMP standard linkup trap for the switch: T1700G-28TQ(config)# snmp-server traps snmp linkup 232 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 247
) Example Enable SNMP link status trap for port 1/0/3: T1700G-28TQ(config)# interface gigabitEthernet 1/0/3 T1700G-28TQ(config-if)# snmp-server traps link-status 29.10 snmp sent when CPU usage exceeds the predefined threshold. By default, the CPU usage threshold of the switch is 80%. 233 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 248
backup, reset, firmware upgrade, configuration import, etc. loopback-detection -- Enable loopback-detection trap. It is sent when the switch detects Mode Example Enable SNMP extended bandwidth-control trap for the switch: T1700G-28TQ(config)# snmp-server traps bandwidth-control 29.11 snmp-server - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 249
Mode Global Configuration Mode Example Enable all SNMP extended MAC address-related traps for the switch: T1700G-28TQ(config)# snmp-server traps mac Enable new MAC address trap only for the switch: T1700G-28TQ(config)# snmp-server traps mac new 29.12 snmp-server traps vlan Description The snmp - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 250
Groups. After a history group is configured, the switch collects network statistics information periodically, based on which default is 50 buckets. Command Mode Global Configuration Mode Example Configure the sample port as Gi1/0/2 and the sample interval as 100 seconds for the entry 1-3: T1700G-28TQ - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 251
to 16 characters. By default, it is "monitor". Command Mode Global Configuration Mode Example Configure the user name of entry 1, 2, 3 and 4 as user1, the description of the event as description1, the type of event as log and the owner of the event as owner1: T1700G-28TQ(config)# rmon event 1-4 user - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 252
monitored variable exceeds the threshold, an alarm event is generated, which triggers the switch to act in the set way. Syntax rmon alarm index { stats-index -- Specify the statistics index. alarm-variable -- The alarm variable. By default, the option is revbyte. s-type -- Sample Type, which is the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 253
, ranging from 10 to 3600 in seconds. By default, it is 1800. Command Mode Global Configuration Mode Example Configure rmon alarm entries 1-3 binding with statistics entry 2, the owners as owner1 and the alarm intervals as 100 seconds: T1700G-28TQ(config)#rmon alarm 1-3 stats-index 2 owner owner1 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 254
creator of the event entry, ranging from 1 to 16 characters. By default, it is "monitor". status -- The status of the statistics entry, EXEC Mode and Any Configuration Mode Example Display SNMP configuration globally: T1700G-28TQ# show snmp-server 29.18 show snmp-server view Description The show - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 255
used to display the Group table. Syntax show snmp-server group Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Group table: T1700G-28TQ# show snmp-server group 29.20 show snmp-server user Description The show snmp-server user command is used to display the User table - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 256
to display the Host table. Syntax show snmp-server host Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Host table: T1700G-28TQ# show snmp-server host 29.23 show snmp-server engineID Description The show snmp-server engineID command is used to display the engineID of - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 257
select more than one entry for each command. By default, the configuration of all history sample entries is displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of all history sample entries: T1700G-28TQ# show rmon history 29.25 show rmon event - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 258
select more than one entry for each command. By default, the configuration of all Alarm Management entries is displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of the Alarm Management entry 1-2: T1700G-28TQ# show rmon alarm 1-2 29.27 show rmon - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 259
entry is automatically created and maintained by ARP. A static ARP entry is manually configured and maintained. 30.1 arp Description This arp command is used to Example Create a static ARP entry with the IP as 192.168.0.1 and the MAC as 00:11:22:33:44:55: T1700G-28TQ(config)# arp 192.168.0.1 00:11: - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 260
the aging time, ranging from 1 to 3000 seconds. The default value is 600 seconds. Command Mode Interface Configuration Mode Example Configure the ARP aging time as 60 seconds on interface 1/0/1: T1700G-28TQ(config)# interface gigabitEthernet 1/0/1 T1700G-28TQ(config-if)# arp timeout 60 30.4 show arp - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 261
ARP entry. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the ARP entry with the IP as 192.168.0.2: T1700G-28TQ(config)# show ip arp 192.168.0.2 30.5 show ip arp (interface) Description This show arp command is used to display the active ARP entries associated with - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 262
Syntax show ip arp summary Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the number of the ARP entries: T1700G-28TQ(config)# show ip arp summary 248 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 263
no interface vlan { vid } Parameter vid -- The ID of the VLAN. Command Mode Global Configuration Mode Example Create the VLAN interface 2: T1700G-28TQ(config)# interface vlan 2 31.2 interface loopback Description This interface loopback command is used to create the loopback interface. To delete the - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 264
range ten-gigabitEthernet / interface port-channel / interface range port-channel) Example Switch the gigabitEthernet port 1/0/9 into the routed port: T1700G-28TQ(config)# interface gigabitEthernet 1/0/9 T1700G-28TQ(config-if)# no switchport 31.4 shutdown Description This shutdown command is used - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 265
as 192.168.2.0, the subnet mask as 255.255.255.0 and the next-hop address as 192.168.0.2: T1700G-28TQ(config)# ip route 192.168.2.0 255.255.255.0 192.168.0.2 31.6 description Description This description command is used to add a description to the Layer 3 interface, including routed - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 266
ID. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of VLAN 2: T1700G-28TQ(config)#show interface vlan 2 31.8 show ip interface Description This show ip interface command is used to display the detailed information of the specified Layer 3 interface. 252 - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 267
EXEC Mode and Any Configuration Mode Example Display the detailed information of the VLAN interface 2: T1700G-28TQ(config)# show ip interface vlan 2 31.9 show ip interface brief Description This show ip interface brief command is used to display the summary information of the Layer 3 interfaces - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 268
The connected routes. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the static routes: T1700G-28TQ(config)# show ip route static 31.11 show ip route specify Description This show ip route specify command is used to display the valid routing information to the specified - TP-Link T1700G-28TQ | T1700G-28TQ V1 CLI Reference Guide - Page 269
Display the routes to all the subnets that belongs to 192.168.0.0/16: T1700G-28TQ(config)# show ip route specify 192.168.0.0 255.255.0.0 longer-prefixes 31.12 show ip route summary Description This show ip route summary command is used to display the summary information of the route entries
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
 |
 |
T1700G-28TQ
JetStream 24-Port Gigabit Stackable
Smart Switch with 4 10GE SFP+ Slots
REV1.0.0
1910011380