Toshiba 50L1350U User's Guide for L1350U and L2300U Series TV's - Page 47

Installation, Channel Tuning, ENTER, Auto Tuning, Channel Program menu - service menu

Get Toshiba 50L1350U PDF manuals and user guides View all Toshiba 50L1350U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

47 Setting up your TV Auto Tuning v You must set up the ANT/CABLE input source before programming channels. See "ANT/CABLE IN" on page 45. v The automatic channel programming process will erase channels that were previously programmed into the TV's memory. v To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. v Programming channels when the ANT/CABLE input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly. To program channels automatically: 1 Configure the antenna input source, if you have not already done so, see "ANT/CABLE IN" on page 45. 2 Press the MENU button and open the Installation menu. 3 Highlight Channel Tuning, and then press the ENTER button. (Sample Image) Setup menu - Installation selection 4 Highlight Auto Tuning, and then press the ENTER button to open the Channel Program menu to begin channel programming. ! Cable Scanning channels, please wait... 6% Number of Channels Found - 7 Scanning Analog Channels Channel - 9 Cancel (Sample Image) Installation menu - Channel selection

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
47
Setting up your TV
Auto Tuning
v
You must set up the ANT/CABLE input source before
programming channels. See
“ANT/CABLE IN” on page 45.
v
The automatic channel programming process will erase
channels that were previously programmed into the TV’s
memory.
v
To tune the TV to a channel not programmed in the channel
memory, you must use the
Channel Number
buttons on the
remote control.
v
Programming channels when the
ANT/CABLE
input is
configured for Cable will take substantially longer than when the
antenna input is configured for Antenna. This is normal;
however, once channel programming is finished, you should not
have to repeat the programming process again unless your Cable
TV service lineup changes significantly.
To program channels automatically:
1
Configure the antenna input source, if you have not already
done so, see
“ANT/CABLE IN” on page 45.
2
Press the
MENU
button and open the
Installation
menu.
3
Highlight
Channel Tuning
, and then press the
ENTER
button.
(Sample Image) Setup menu - Installation selection
4
Highlight
Auto Tuning
, and then press the
ENTER
button to
open the
Channel Program menu
to begin channel
programming.
Cable
Scanning channels, please wait...
Number of Channels Found
-
7
Scanning Analog Channels
6%
Channel
-
9
Cancel
!
(Sample Image)
Installation menu - Channel selection