Tripp Lite PDU3VSR6L2130 Owner's Manual for SNMPWEBCARD 9332CE - Page 71

IPV6 Settings

Get Tripp Lite PDU3VSR6L2130 PDF manuals and user guides View all Tripp Lite PDU3VSR6L2130 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

4. Telnet/SSH Console continued 4.3 Network Configuration continued 4.3.1.4 IPV6 Settings This menu displays current IPV6 settings and allows a user to toggle the dynamic host configuration protocol and method. There can be up to six IPV6 addresses for the card. Only two of these are impacted by this menu. A user may choose to have one IPV6 Address determined through DHCP and one set statically. Any others that appear in the list have been automatically assigned by the card's software. They are shown here because they are valid IP addresses and can be used to route to the card. These addresses will have a method of AUTO. -------- IPV6 Settings Current IPV6 Address Information Home -------eth0:1 eth0:3 eth0:4 eth0:5 eth0:6 eth0:7 Method IPV6 Address Prefix Length -------- STATIC 2001:DB8::1:58:4F43:4849:544C 64 AUTO FE80::240:9DFF:FE43:3597 64 AUTO 2001:DB8::1:240:9DFF:FE43:3597 64 NONE :: 0 NONE :: 0 NONE :: 0 Settings On Restart DHCP : Yes Static : Yes Address : 2001:DB8::1:58:4F43:4849:544C Prefix Length : 64 1- DHCP 2- Static 3- Address 4- Prefix Length A- Apply Changes X- IP Configuration M- Return to Main Menu Refresh Menu Menu Data DHCP This setting determines if an IPV6 address should be obtained through DHCP. Static This setting determines if the user wishes to assign a static IPV6 address. Address If "Static" is Yes, then the address must be specified. If No, the address will not be displayed. Prefix Length If "Static" is Yes, then the prefix length must be specified. If No, then the prefix length will not be displayed. 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
71
4. Telnet/SSH Console
continued
4.3 Network Configuration
continued
4.3.1.4 IPV6 Settings
This menu displays current IPV6 settings and allows a user to toggle the dynamic host configuration protocol and method. There can be up to
six IPV6 addresses for the card. Only two of these are impacted by this menu. A user may choose to have one IPV6 Address determined through
DHCP and one set statically. Any others that appear in the list have been automatically assigned by the card’s software. They are shown here
because they are valid IP addresses and can be used to route to the card.
These addresses will have a method of AUTO.
-------- IPV6 Settings ---------------------------------------------------------
Current IPV6 Address Information
================================
Home
Method
IPV6 Address
Prefix Length
-------- -------- ------------------------------
--------------
eth0:1
STATIC
2001:DB8::1:58:4F43:4849:544C
64
eth0:3
AUTO
FE80::240:9DFF:FE43:3597
64
eth0:4
AUTO
2001:DB8::1:240:9DFF:FE43:3597
64
eth0:5
NONE
::
0
eth0:6
NONE
::
0
eth0:7
NONE
::
0
Settings On Restart
===================
DHCP
: Yes
Static
: Yes
Address
: 2001:DB8::1:58:4F43:4849:544C
Prefix Length
: 64
1- DHCP
2- Static
3- Address
4- Prefix Length
A- Apply Changes
X- IP Configuration
M- Return to Main Menu
<ENTER> Refresh Menu
Menu Data
DHCP
This setting determines if an IPV6 address should be obtained through DHCP.
Static
This setting determines if the user wishes to assign a static IPV6 address.
Address
If “Static” is Yes, then the address must be specified.
If No, the address will not be displayed.
Prefix Length
If “Static” is Yes, then the prefix length must be specified.
If No, then the prefix length will not be displayed.